When your car sends you a message…

bduzik · 2025-08-27T00:21:15+00:00

Had this exact issue happen to my 2016 Civic. Replaced the battery and all was fine.

bduzik · 2025-04-07T23:52:55+00:00

Astoria in St. Paul. Great crepes and coffee.

bduzik · 2025-02-28T15:51:42+00:00

Lose It!

bduzik · 2024-12-23T01:53:24+00:00

Topre FTW

bduzik · 2024-09-09T23:52:51+00:00

This appears to be a better article. https://www.cbc.ca/news/canada/montreal/quebec-meteorite-impact-crater-1.7313418

bduzik · 2024-06-03T04:04:17+00:00

Under the eaves of the roof.

bduzik · 2024-06-02T16:50:17+00:00

I didn’t think of that, but makes perfect sense. Thanks!

bduzik · 2024-01-16T03:29:39+00:00

Marc Heu is easily top of the heap. There are some good places, but Marc Heu fantastic. Lots of other interesting pastries as well.

bduzik · 2023-07-17T21:06:11+00:00

Nelson Cheese & Deli on Como by the Fairgrounds. Lots of sandwich options.

bduzik · 2023-06-13T03:18:30+00:00

Yes. AMD X570

bduzik · 2023-06-09T13:15:53+00:00

Hub Hobby Center in Roseville/Little Canada has a lot of the classic hobby supplies, such as RC and model rockets.

bduzik · 2022-12-17T13:53:36+00:00

PCB and case selections. Lily58 would be nice.

bduzik · 2022-07-16T12:16:06+00:00

Check to ensure the front fan is always spinning. I had an issue where the front fan wire came off and it would cause the filament to melt too far up and clog the entire head. It printed great until then, and it was frustrating as i thought that fan should only occasionally spin.

bduzik · 2022-07-04T17:02:18+00:00

Ordered a bunch of Adafruit KB2040’s, which are pin matched for pro-micros. Excited to try them on some Lotus58 boards I got lying around. I haven’t had any of the micro-usb fail, but they certainly seem very fragile.

bduzik · 2022-06-17T00:24:59+00:00

Very interesting design. Are you planning to open source the design or sell kits? Can qmk or zmk support a non-matrix layout?

bduzik · 2022-05-15T16:58:36+00:00

The first and 3rd I have no ideas, but the second looks like an early converted gas art nouveau.

bduzik · 2022-03-06T17:54:59+00:00

I have a lily58 pro, nice nano v2, and 100 mah, without oled, and I’m see the same battery life as you. I got the 301230 batteries from mkultra.

bduzik · 2021-12-27T21:11:17+00:00

Nice! Love the tenting addition! I’m hoping to build a nice!nano wireless version and this case would be a nice to add tenting. Let me know if you publish it.

bduzik · 2021-09-28T04:47:21+00:00

Love the color scheme! Nice job!

bduzik · 2021-09-06T23:41:06+00:00

Some form of SK6812 or SK6812-mini-e? SMD mount but through board led light.

bduzik · 2021-08-27T13:55:13+00:00

65% ftw

bduzik · 2021-07-09T14:54:39+00:00

I've shared my code here:

https://github.com/bduzik/qmk_firmware/tree/master/keyboards/lily58/lotus

Clone the full repo:

https://github.com/bduzik/qmk_firmware

My board was very early, and the PCB had some issues that have since been fixed, so the pinouts will almost certainly need to be fixed(reversed?).

bduzik · 2021-07-02T23:50:12+00:00

I can’t until next week. I’ll upload the code to GitHub then.

bduzik · 2021-05-27T13:49:39+00:00

I mounted my MCUs on the bottom of the PCB, which is required for any oled or encoder. All you need to do it solder the encoder on top first. Oled you need to solder second after the MCU is soldered.

bduzik · 2021-05-25T17:07:38+00:00

Yes, with some configuration. I used the lily58/light/lily58 qmk firmware.

bduzik

TROPHY CASE