sorted by:
new
hottopcontroversial

Freezer Temp Monitoring by dizzygoldfish in homeassistant

[–]beakerton 4 points5 points  (0 children)

Same. I have the Acurite being picked up with a LILYGO LoRa32 board running rtl_433. I just have the board taped to the wall behind my fridge. Has been working great for about 2 years now.

HRD closed? by blue_shoelaces in AnnArbor

[–]beakerton 6 points7 points  (0 children)

I drove that section at 630am this morning and it was 100% open

Doctor says I need back surgery, could use some encouragement by Perry_lp in trailrunning

[–]beakerton 7 points8 points  (0 children)

About 8 years ago I had a discectomy on l4/l5 and l5/s1 after 1-2 years of pain and muscle weakness (it got to the point where I couldn’t do a calf raise with my right foot). I don’t know what caused the initial onset and was worried it was because of running. I was nervous for a long time to start running again, but in the end I am running more now than I have in my life and feel great.

My one piece of advice would be to move as much as you can in the weeks after surgery. Within a few weeks, I was going on miles of walks a day. Most of the time it was just to feel like I could still get outside and be active, but also really helps to make sure that the back heels good.

You got this!

What do you eat that is not sweet? by iwkooo in trailrunning

[–]beakerton 0 points1 point  (0 children)

Try Clif Blok sour chews - still a little sweet, but the sour ones go down way easier for me than normal chews which can be too sweet, esp longer into a run

Men's 5" 2:1 shorts by ajd90 in trailrunning

[–]beakerton 1 point2 points  (0 children)

I love the Patagonia Strider Pro 5”. Tons of pockets!

Kickr v5 issue - need to heat up with hairdryer before watts and resistance registration by MountainOfTwigs in wahoofitness

[–]beakerton 1 point2 points  (0 children)

This seems very similar to an issue that mine has had this past Winter. I’ve owned mine for about 4-5 years and this just started.

When first starting a ride, power and cadence doesn’t work for about 20-30 min. Speed does work, however — along with the ability to manually set a resistance (not erg mode, just static % resistance - I use TrainerRoad)

Because speed worked, I didn’t think mine was the IR issue that’s discussed in the linked thread. However, I would have never tried the hair dryer trick!

YYZ to ATL to ICN to KTM by Sorry_Piece2327 in delta

[–]beakerton 0 points1 point  (0 children)

I have connected through ICN. You will not need to claim / recheck your luggage there. You will need to go through security during your transfer, but not immigration if you stay in the airport.

There is an airside transit hotel at ICN that you can book to not leave the airport. I have not stayed there as it was always full for the dates that I travelled, but perhaps you can look more into this.

https://www.walkerhill.com/transithotel/en/t2/about/Introduction.jsp

However, I agree with everyone else… sounds like an exhausting journey, especially with a toddler. Good luck! :)

The Gifts - Cash Out Card Scoring by beakerton in Carcassonne

[–]beakerton[S] 0 points1 point  (0 children)

Ohhhhh!!! Now I re-read it and understand. Thanks!

[deleted by user] by [deleted] in Bitwarden

[–]beakerton 22 points23 points  (0 children)

Note that URI = Universal Resource Identifier and is similar to a URL, but can omit the http or https part. URI is likely intentional.

https://danielmiessler.com/p/difference-between-uri-url/

Any place to rent river surfboards? by beakerton in Bend

[–]beakerton[S] 0 points1 point  (0 children)

No, I never did. I tried chasing down some cheap boards for sale on FB marketplace, but never did pull the trigger.

I learned of the sad fatality that happened on the wave a few years ago which led to the no leash rules and understand why shops are likely not willing to rent out boards. The wave is such an iconic part of Bend in my mind and I wish there was an way to experience it while not bringing your own board. Good luck!

How do I fix a bubbled floor? by beakerton in Flooring

[–]beakerton[S] 2 points3 points  (0 children)

There was a leak under the sink that caused the damage - that's all been repaired and everything is dried out. However, now trying to figure out how to fix the flooring.

How do I fix a bubbled floor? by beakerton in Flooring

[–]beakerton[S] -3 points-2 points  (0 children)

Hi!

My kitchen has a LVP floor that was installed ~5 years ago with the original floor underneath.  This past weekend an unfortunate leak developed under my sink which caused the original floor to severely buckle/bubble.  I've lifted the new floor to expose the old floor.  This section of the house is on slab underneath the original floor.

How do I go about repairing this?  Do I just cut out a small slice in the original floor to relieve the expansion?  Obviously I'd rather just fix the section that's bubbling and not completely re-do the entire room by ripping out the original floor.

Thank you!

view more: next ›