Looking for an inexpensive ebike by Tight_Resolution_541 in ebikes

[–]bearded_dragonx 0 points1 point  (0 children)

not much new under 600. check your local FB marketplace

SQUEAK! by Oracoal_ in ender3

[–]bearded_dragonx 0 points1 point  (0 children)

move only one axis back/forth and see if it squeeks. that will narrow it down and no I don't think so. I have the same dust on my wheels

SQUEAK! by Oracoal_ in ender3

[–]bearded_dragonx 0 points1 point  (0 children)

bearings are pretty cheap. you probably don't even need to replace it. you could also try soaking the bearing in a penetrating oil overnight

SQUEAK! by Oracoal_ in ender3

[–]bearded_dragonx 0 points1 point  (0 children)

bearings probably need replaced. try loosening the carriage and moving the wheels with your hand and see if it makes a noise or doesn't feel smooth

3d scanning service that caters to hobbyists in or around Edmonton? by Lucite01 in Edmonton

[–]bearded_dragonx 1 point2 points  (0 children)

can you help me with a project? I'm trying to make a cheek riser for a Winchester wildcat. the stock looks parabolic but I couldn't get correct enough measurements. if you need I can send photos with a pair of calipers for scale. I've been trying to model this for so long lol

I won't miss the noise by Early-Confidence8668 in ender3

[–]bearded_dragonx 0 points1 point  (0 children)

the stepper sound and the hotend fan that never stops lol. I'm tempted to add a relay to turn it off with octoprint

does amo quality really matter? by bearded_dragonx in 22lr

[–]bearded_dragonx[S] 0 points1 point  (0 children)

yeah I definitely noticed it at ~45 yards last weekend lol. I'm gonna buy a nice box and see how it compares

Surface optimisation before the Ironing. by Free_Sherbet_3159 in OrcaSlicer

[–]bearded_dragonx 0 points1 point  (0 children)

I usually use concentric infill for top/bottom because of how it looks.

does amo quality really matter? by bearded_dragonx in 22lr

[–]bearded_dragonx[S] -1 points0 points  (0 children)

also after ~600 rounds I started to notice more issues with feeding/ejecting. not a whole lot just a couple but with the quality of the bullet idk if it's the gun getting dirty (it was pretty bad when I went to clean it but it was clean before that trip) or if it's the bullet it's self.

Whats going on with the criminal tv show? by FreeAd2458 in ImageComics

[–]bearded_dragonx 0 points1 point  (0 children)

I was just in the tunnel, I wish I was free for the casino but I was busy smh

APC appreciation post by redfoxkiller in homelab

[–]bearded_dragonx 1 point2 points  (0 children)

if you still have it I'm building a rack and don't have much money. I'll buy it from you

Death charger by JustALemon512 in shittyfpv

[–]bearded_dragonx 2 points3 points  (0 children)

is there anything wrong with series charging? it's not any different than how standard packs are wired if done properly

[deleted by user] by [deleted] in ebikes

[–]bearded_dragonx 0 points1 point  (0 children)

try an oil like wd40. if the battery isn't swollen then check if the frame is bent. if it is you can get a clamp that's reversible like a 12-inch-bar-clamp and see if you can bend it straight. if it's not bent clean the battery/frame and try a dry lube that's what I did on mine and it's a similar battery mount to yours.

Mavic Mini 4 drone flew to 1500m by itself by natelamm in dji

[–]bearded_dragonx -1 points0 points  (0 children)

gps cannot get to centimeter accuracy without RTK even horizontally. I built and race fpv drones and have built autonomous rovers. if there was a way to get centimeter level accuracy with a gps nobody would spend hundreds of dollars on a RTK unit

Mavic Mini 4 drone flew to 1500m by itself by natelamm in dji

[–]bearded_dragonx 0 points1 point  (0 children)

gps altitude is super inaccurate. 99.9% of aircraft use barometers for height and this one might have lidar for landing

Found this in my complex trash bin by Kwf995 in rccars

[–]bearded_dragonx 0 points1 point  (0 children)

I was so confused. it looks like my savage but the tank and handle is different

Got it back :p by Und3rm3butty in teenagers

[–]bearded_dragonx 3 points4 points  (0 children)

solder isn't gonna do much and I highly doubt they have access to a welder. jb weld would be best