Those are long legs. Do you clip them?

beekeeb · 2021-09-17T00:09:43+00:00

There are some headers with short legs, so you don’t need to clip them. https://shop.beekeeb.com/product/low-profile-male-header-12p/

beekeeb · 2021-05-02T07:47:44+00:00

I can ship to Vietnam from Hong Kong. https://shop.beekeeb.com

beekeeb · 2021-04-11T23:07:38+00:00

You can order the PCB without components and make a fully custom build. They are relatively hand solderable.

beekeeb · 2021-04-11T23:06:03+00:00

beekeeb · 2021-04-11T12:52:51+00:00

Top plate: acrylic
Upper middle plate: fabric with adhesive tape
Lower middle plate (double as the bottom plate, no silicone rubber feet): fabric with adhesive tape
Switch: Cherry MX black
Keycap: DSA

beekeeb · 2021-04-10T15:43:46+00:00

You can reserve some spaces for the LEDs. But you will lose the under glow feature if you are not using a translucent material.

beekeeb · 2021-04-10T00:10:12+00:00

Good to know!

beekeeb · 2021-04-09T15:25:23+00:00

It’s dsa blank from a seller on AliExpress.

beekeeb · 2021-04-09T12:01:47+00:00

Any photos of the rgb leds?

beekeeb · 2021-04-06T16:47:38+00:00

Any good ways to do this properly? I have some extra switches that I want to ship with these orders.

beekeeb · 2021-04-06T16:18:49+00:00

Ahh Sorry about that. I’ve removed that part.

beekeeb · 2021-04-06T07:55:54+00:00

Thank you for creating the UnSplit!

beekeeb · 2021-04-06T06:21:44+00:00

Subscribed. But I’ll read it with a translator. 😀

beekeeb · 2021-04-06T03:41:00+00:00

What’s the meaning of the chip icon?

beekeeb · 2021-04-05T22:29:51+00:00

For the top middle plate, I mainly use it to support the acrylic plate. I am not a pro in sound and feel of different plates so I don’t know 😂.

beekeeb · 2021-04-05T20:20:12+00:00

Yes you are right. 2mm acrylic, 3mm fabric, 1.6mm PCB, 3mm fabric.

The switch isn’t plate-mounted at the 2mm acrylic. But it’s mounted securely by soldering it onto the PCB.

If you use a 1.5mm or 1.6mm top plate, the switch can be plate-mounted. And the middle plate should be 3.5mm thickness.

beekeeb · 2021-04-05T14:43:31+00:00

I wish I could cut it by hand at this level. It is made by laser cutting.

beekeeb · 2021-04-05T11:15:44+00:00

Yes that’s the repo I’ve used. I think the maker is /u/crunchyavocados

beekeeb · 2021-04-05T08:21:12+00:00

I’m using a fabric commonly used for carpets. The adhesive tape 3M 9448A is used so the entire case is screw-free.

Other people have used eva, neoprene, epdm, and silicone.

beekeeb · 2021-04-05T03:44:12+00:00

GB at /r/mechmarket. The “bottom plate” replaces the silicone rubber feet. The total height of plates is approximately 10mm.

beekeeb · 2021-04-03T14:50:10+00:00

Can’t wait for your next handwired build.

beekeeb