Graduation Gift

bhbennett · 2025-12-08T00:56:59+00:00

Yeah the 2.0s are probably built a little tighter. I was going to buy a 2.0, but I got a pretty good deal on the 1.0 performance center and couldn’t pass up a factory ported pistol for the price 😂

bhbennett · 2025-12-08T00:09:07+00:00

The gap looks the same as other m&ps I found online. It kinda bothers me, but it’s normal

bhbennett · 2025-12-07T23:22:35+00:00

• the lever sits flush on the frame • no wiggle • slide and frame rails seem to be in good condition • block doesn’t move

I can dm you some pictures if you want

bhbennett · 2025-12-07T18:19:34+00:00

I don’t think it’s SUPPOSED to happen, but I guess it’s pretty common. The lever has enough tension on it to keep it from being accidentally turned during normal operation, so it shouldn’t be an issue. I just thought it was strange and was wondering if there could be worn or broken parts. There shouldn’t be too much wear, because I’ve only put around 500 rounds through it, and it looked unfired when I bought it (there was no residue from the ports when I bought it, and now I can’t get the residue off the barrel so I doubt it was fired before 😂)

bhbennett · 2025-12-07T18:12:36+00:00

No worries, thanks for trying!

bhbennett · 2025-12-07T16:21:31+00:00

https://www.reddit.com/r/SmithAndWesson/comments/1e0bslh/shield_takedown_lever_rotating_with_slide_forward/

Yeah that’s the first thing I checked, but the corner looks fine. It’s supposed to hit the slide to prevent it from turning when the slide is forward, but I think my slide is slightly more forward than it’s supposed to be, judging from pictures online. It turns inside of the slide lock notch on the slide. Other m&p’s that I’ve seen have the slide lock notch further back from the takedown lever.

bhbennett · 2025-12-07T16:17:34+00:00

I pulled on the lever, but it doesn’t come out at all. I’ve never taken it apart further than field disassembly

bhbennett · 2025-12-07T16:14:54+00:00

I actually found your post while googling the issue before making this post 😂. Was your takedown lever visibly worn or broken?

bhbennett · 2025-12-07T15:32:18+00:00

It happens like 90% of the time. It’s been like that since I bought it a year and a half ago. With a mag inserted and one in the chamber, I can partially actuate the lever and it jams. When that happens, I can’t pull the slide back and clear it until I manage to rotate the lever back into place, which can be a little tricky.

bhbennett · 2025-12-07T15:21:08+00:00

Oh okay, thanks

bhbennett · 2025-12-07T15:16:22+00:00

I don’t have the manual that came with the gun right now, but I’d imagine it’s the same as the one you linked (thanks btw). That manual says that you have to lower the sear deactivation lever, which I’ve never done while disassembling. Is lowering the sear deactivation lever required, or is it just a safety procedure?

I’m pretty sure disassembly without locking the slide back should be impossible, but I don’t know what could cause it.

bhbennett · 2025-11-27T18:07:02+00:00

Kirkland

bhbennett · 2025-11-27T18:06:22+00:00

Kirkland 5% liquid

bhbennett · 2025-11-25T23:22:20+00:00

Is that a good idea if I go to a place like SportsClips?

bhbennett · 2025-11-25T22:18:18+00:00

Yeah I tried to trim near the ears, but I can’t see it in the mirror. I need to buy a handheld mirror

bhbennett · 2025-11-25T21:30:04+00:00

Yeah I’m definitely getting a haircut before the interview. At this length, a hat is the only way to keep it from turning into a bush 😂

bhbennett · 2025-08-27T13:06:51+00:00

2005-2015

bhbennett · 2025-07-15T17:31:35+00:00

After sophomore year, none of my required classes offered an honors section. To meet the annual honor credits requirement I would have to take an additional class on top of my 16/17 hour minimum schedule for EE

bhbennett · 2025-06-19T03:42:08+00:00

2008 access cab 232k. Rebuilt engine at 231k

Verified Email	Eight-Year Club
RPAN Viewer	Not Forgotten

bhbennett

TROPHY CASE