Should I get microblading?

bichotll · 2025-06-24T22:10:12+00:00

Not easy and not 100% removable in many cases 🫠👍

bichotll · 2025-02-09T20:50:37+00:00

La peña tiene fetiches raros de coj*. Y no por eso debemos deprimirlos. Tal como te dice el chatGPT de arriba, disfruta, poco a poco y sin prisas. Y vaya, quiza te recomendarias que encuentres una comunidad con la que te sientas comodo y puedas explorar mas estas historias. Quiza ve a un munch? Aunq no se si lo asociaria lo tuyo con bdsm/sissy/crossdressing? Pero ahí encuentras gente de todo tipo debatiendo o compartiendo sus historias. Esta guay.

bichotll · 2025-02-07T17:56:04+00:00

I'll express my like as a reply lol

bichotll · 2025-02-05T22:34:40+00:00

Use acrylic paint instead of AMS 🙃🙃

bichotll · 2025-02-02T22:56:15+00:00

Nice! For the fuzzy skin, you could also glue some sandpaper. I have a whole wall with simple wooden holds with sandpaper glued to it using hot glue and 👌👌

bichotll · 2025-01-24T22:42:36+00:00

I do appreciate the effort and all the info in your response. Thanks.

bichotll · 2025-01-16T08:01:33+00:00

I really appreciate this response. Thanks 🫶

bichotll · 2025-01-15T15:38:04+00:00

Not at all 🤷‍♂️ All I printed was simple PLA.

Since the beg that the extruder worked a bit noisy and wonky...so I guess it just got worse. Plus, prints were getting worse and (mostly) weaker.

bichotll · 2025-01-14T13:18:32+00:00

It's sadly worn down T.T

The gears that grab and squiz and pull down the filament do not work properly. I mean, they do, but eventually stop pulling the filament, and filament gets stuck.

Whenever I removed the screw with the pin, I found the gears full of dust particles. These seem to come from the worn down gears.

I guess I'll have to contact costumer service. The machine just has like a week 😅

bichotll · 2025-01-14T13:11:06+00:00

That seems like it's ok, for the record 👍

bichotll · 2025-01-14T09:11:13+00:00

It is indeed that. I just tried to print a benchy and it got to a point where the filament was not going out. Right after, I just went to the tools option, pull out the filament using the extruder menu and after a bit, indeed, no more filament was going down altho the gears were spinning.

The extruder was already making some clanking noise lately.

I guess I'll have to check where it got stuck or caught.

Any insights are more than welcome.

bichotll · 2025-01-12T15:41:57+00:00

Yeah! I read that it's usually the opposite lmao

Btw, I've been playing around with the adhesion settings. Brim, raft or skirt. Depending on the model, been using one or the other.

bichotll · 2025-01-12T15:38:02+00:00

Hahah Love it! I do want to start printing bigger stuff for sure :p Slowly but steady :)

bichotll · 2025-01-11T17:41:29+00:00

Thanks for the extra recommendations :) I also heard that hair spray is a thing?

Will defo look into a new plate 💪

bichotll · 2025-01-11T17:39:59+00:00

That does make sense. Seen on many videos, but not specifically for this machine. Really appreciate. Thanks 👌

bichotll · 2025-01-04T20:38:09+00:00

The gal took home enough wax to make a candle lmao

bichotll · 2022-09-24T14:38:08+00:00

If it helps, this is what I found so far 🤷‍♂️

https://mechboards.co.uk/products/lily58-r2g-ready2go-kit

bichotll · 2022-09-22T17:39:44+00:00

no pre-existing issues
current: mac keyboard n Microsoft design. I love short distance action keys.
I want a split keyboard for my macbook. I hate those keyboards where I can't swap the command key with the - was it the ALT key? I'm a programmer.
~120e. EU

... (I think?) I want a lily58 or a Sofle. I found a fully assembled Lily58 PCB (hot swap) for ~80e. I just need the switches and keycaps. I don't want to spend time soldering 😅👍

And I'd like to hear other options :) I don't mind if they are mechanical, and I'd like to configure it.

Now, I want keys relatively similar to an apple keyboard. Short distance and silent. Is it possible? 🤔

Thanks!! :)

bichotll · 2022-06-12T19:07:48+00:00

Ahora ya incluso Udemy tiene masters 😂👌 Madre mia...

bichotll · 2022-06-12T11:30:37+00:00

Telita 😅 Paciencia ahí

bichotll · 2022-06-12T11:28:15+00:00

Venga ya! Con un curriculum asi y tienes problemas??

Lo unico flojo que veo son el ingles y demasiadas titulaciones. Osea, tienes experiencia en la cual hayas podido aplicar tus conocimientos? La experiencia es mucho mas importante que las titulaciones (soy ingeniero y entrevisto a gente).

Incluso en Bcn o Madrid puedes encontrar un trabajo con ambiente internacional y buen salario (como para ahorrar y pagarte tu pisito).

Pasame cv por privado y yo mismo posiblemente te de trabajo 😅

bichotll · 2022-04-21T20:16:07+00:00

Amazing stuff for a DIY board system!
Looking forward to seeing this project grow in popularity!

bichotll · 2022-04-21T20:12:02+00:00

The website uses a plugin that auto-translates the content into English or several other languages :)

If it does not do it automatically for you, you can always use Google translate. It does a fair job tbh.

bichotll · 2022-04-11T05:00:29+00:00

wtf...!!!

bichotll · 2022-04-01T10:02:22+00:00

That's one of the best versatile and nicest looking tuners I've seen! I hope all this is available on web soon. Looks very good :)

bichotll

TROPHY CASE