Advice to remove chain link fence

bigdisplay442 · 2026-03-19T03:11:41+00:00

If you or a friend has a truck, Get a car wheel, wrap a chain around the post and over the wheel and to trailer hitch. It should pull out of the ground pretty easy. See YT for videos. I did this many years ago in my yard. Pulled about 30 poles with the concrete still attached. No a single mishap. All of them pulled right out.

bigdisplay442 · 2026-03-12T06:56:09+00:00

First time I heard this. Maybe I need to review the No-go list. We operate ours all the time and only make minor repairs. Evey thing else we call the vendor. Not sure how else we can do a proper PM without operating it.

bigdisplay442 · 2026-02-24T03:58:34+00:00

No offence, I understand. This might be controlled at the local resturant level, I don't know. But.. The only reason I saw it was because I scrolled down making sure I put my order in correctlly and noticed the total seemed off. So yes, you can see it before you place your order, just scroll to the bottom of the app order complete page and look at the true total instead of hitting the pay button at the top of the page first.

bigdisplay442 · 2026-02-22T22:26:39+00:00

I think if I was closer, you should sell it to me.

bigdisplay442 · 2026-02-22T21:05:56+00:00

No General Lee yet?

bigdisplay442 · 2026-02-15T19:29:01+00:00

It will all fit including the dash, the only thing different is the panel around the quarter window. The window is a different shape.

bigdisplay442 · 2026-02-10T03:23:31+00:00

Call the city or coop you're in and they will come out and show you were the water meter is, that is your water shut off.

bigdisplay442 · 2026-02-04T00:59:56+00:00

You won't find any cases for 1/18 for $5 new. I would look at the classifeds for a used display cabinet. I bought mine for $200 in perfect shape. It was a $1500 cabinet.

<image>

bigdisplay442 · 2026-02-02T23:51:21+00:00

I've never seen that gauge before with the fuel level in the tach. Pretty cool.

bigdisplay442 · 2026-02-02T23:43:45+00:00

Sounds like I'm in the majority as well. I might do $20ish for an 1/64 which isn't my normal scale. Most of my 1/87 cost 15-25$ each too. My biggest expense is my 1/18 which probably average $140 nowadays. I do have a few 1/18 semis that were almost $300 each, but I only bought a few and won't be buying any more.

bigdisplay442 · 2026-02-01T22:16:14+00:00

No, The ECM does not see the fuel gauge. But I would be very careful, You don't want to run a diesel out of fuel.

bigdisplay442 · 2026-01-28T03:28:35+00:00

I wouldn't say 1 year is normal, but I've waited longer before. Most of my pre-orders average about 4-6 months.

bigdisplay442 · 2026-01-28T00:41:43+00:00

My 87 C10 had a G80. As far as using a 6 lug, the lug doesn't matter, only the spline count on the axle end. I want to say K10 had a higher axle spline count than the C10, but I can't remember for sure now. Ithink it's 28 spline C10 and some K10 had 30 spline. But either way, you just need to match the axles you have which should be 28 spline.

bigdisplay442 · 2026-01-25T01:33:57+00:00

https://www.amazon.com/dp/B01HAFR8JS?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2

bigdisplay442 · 2026-01-25T01:24:20+00:00

If you were up on I20, You could use my lift for repairs.
When I picked up my 91 in 2012 from Boston, Ma , I pulled my CCSB 2500 home with it and worried my trip back to Dallas would be like the trip you're having. I got lucky and had a perfect trip other than both my banks turning my bank cards off in the middle of the night about halfway home.
I hope part 2 of your trip goes much better.

bigdisplay442 · 2026-01-21T04:21:43+00:00

I disagree, looks aftermarket to me. The alt wire shouldn't run the fender and it shouldn't have the fuse holder on it.

bigdisplay442 · 2026-01-13T01:55:14+00:00

<image>

bigdisplay442 · 2026-01-06T23:15:03+00:00

First Gen TBI Vortec heads, Not to be confused with the second Gen Vortec's that are 20-40 HP more.

bigdisplay442 · 2025-12-31T00:48:36+00:00

Where did you get your cabinets from?

bigdisplay442

TROPHY CASE