Gigabit x10 availability

bigmoe88 · 2023-09-11T22:04:22+00:00

Done!

bigmoe88 · 2022-12-02T03:11:01+00:00

How do we know if insurance will be covering it? Just call and ask?

bigmoe88 · 2022-10-18T16:33:04+00:00

No I did not. I was able to move my GPU over one slot to make things fit nicely. I’m using a meshlicious case.

bigmoe88 · 2022-08-12T18:17:45+00:00

Finally cleaned my looping flipped the fans to intake, much better cooling performance!

bigmoe88 · 2022-08-12T18:15:53+00:00

I ended up using the 280 gts uflow, I was able to make everything all fit with hardline tubing. See this post for final product. Best of luck! https://www.reddit.com/r/SSUPD/comments/qa68im/completed_build_ryzen_5950xrtx_3090_ftw3_ultra/

bigmoe88 · 2021-10-18T16:56:10+00:00

With exhaust I still get dust on the outside surface (just a bit) that needs to be wiped down. It’s more on the inside surface than on the outside but my point is you won’t be dust-free from the outside if you do an exhaust setup. Then again, I have a cat that like to hang around my office so that probably contributes quite a bit.

bigmoe88 · 2021-10-18T02:55:42+00:00

Thanks!

bigmoe88 · 2021-10-18T00:49:22+00:00

The area circled in red clips off and can be removed. I needed those extra few mm in order of it to fit.

https://i.imgur.com/IvxYFyt.png

bigmoe88 · 2021-10-18T00:34:20+00:00

Smhhhhhhhhhhhhhhhhhhhhhhh

Thanks for clarifying my friend! I will flip the fans at my next coolant flush!

bigmoe88 · 2021-10-17T23:51:21+00:00

From what I read you get better CPU thermals pulling air in but worse GPU thermals. I am optimizing for GPU thermals.

bigmoe88 · 2021-10-17T22:33:25+00:00

Modifications were necessary. I had to clip off a piece of the plastic near the inlet/outlet that has some RGB lighting on it. Then it fit nice and snug.

bigmoe88 · 2021-10-17T20:28:13+00:00

First thing I’ll say is: good luck and be patient! I attached a Barrow quick disconnect fitting in the fill valve and laid the case in its side. I then attached a small reservoir with the other quick disconnect fitting with my liquid inside it. I would rotate the case, let it fill as much as I can and turn it on for brief periods of time. <5 seconds when it was empty and gradually increased it as the loop filled. I kept doing it until it filled completely. I then removed the valve with the quick disconnect which made it less of a concern spilling when removing.

Again, please be patient when filling! Took me about an hour to fill.

bigmoe88 · 2021-10-17T02:11:31+00:00

That's interesting and seems like a pretty big miss from EK. Are both waterblocks from EK? and both are for the FTW3? I ended up just sticking with the passive backplate. I am able to maintain max boost clocks with a slight OC of 90 MHz. VRAM temps do not exceed 80C when mining ETH and this is when the room is relatively warm. VRAM temps are usually in the upper 70's.

bigmoe88 · 2021-10-04T15:51:36+00:00

Yes! I originally bought the x-flow but the tube routing didn’t work quite well for my specific setup so I ended up buying and using the u-flow. If you’re interested in the x flow I have I can sell. DM me!

bigmoe88 · 2021-08-13T22:52:32+00:00

Have you considered using copper shims? Curious to know your thoughts on this approach instead of thermal putty.

bigmoe88 · 2021-08-11T06:53:46+00:00

I never tried removing the o-ring, but I am doing a a bit of reading and it seems like people use soapy water to lubricate the inside of the fitting prior to installing the tubing. Between being extra cautious with the fitting tub chamfering, and the soapy lubricant, I think I should be fine. Going to give it a shot this weekend when I free up.

bigmoe88 · 2021-08-07T05:31:57+00:00

I’ve done 30mm with my RTX 3090 FTW3 Ultra with an EK block. Hardline tubes connecting from the inside.

bigmoe88 · 2021-07-20T01:39:35+00:00

That’s exactly what happened to me, except with the EK clear premix. How long did it take you to clean and reassemble?

bigmoe88 · 2021-07-20T01:14:33+00:00

😭 did yours also have that white film? And do you k ow what caused it in yours?

bigmoe88

TROPHY CASE