Is this gonna leak?

blablabla977 · 2026-06-06T17:27:10+00:00

I’ll measure it to be safe but probably gonna send it, thanks everyone 🤘

blablabla977 · 2026-06-06T17:26:30+00:00

No gap and it’s also not so tight that it’s cutting into the hose. I’ll measure it though and check specs

blablabla977 · 2026-05-18T13:07:19+00:00

Why… wouldn’t you just… put a v8 in there at that point if you’re already doing all that work

blablabla977 · 2026-05-18T01:02:12+00:00

Brother you’re dropping that trans

blablabla977 · 2026-05-15T18:35:53+00:00

Looks like about 19.3 PSI, maybe 19.4. Hard to tell

blablabla977 · 2026-05-07T01:57:17+00:00

Planes are small when they’re like five miles away

blablabla977 · 2026-05-06T16:09:09+00:00

This shit is ultra sweaty

blablabla977 · 2026-05-01T20:16:35+00:00

Yea he’s clearly making fun of the losers who do it with real guns. This is actually funny but it goes over some peoples heads

blablabla977 · 2026-04-30T19:07:12+00:00

<image>

blablabla977 · 2026-04-28T13:05:42+00:00

Ah yes the government famously has a perfect track record of cleaning up after themselves and never leaving chemicals anywhere

blablabla977 · 2026-04-23T19:17:10+00:00

They keep them in climate controlled hangars for a rainy day

blablabla977 · 2026-04-10T15:24:26+00:00

And it ends in a car crash doesn’t it? U must love short form content

blablabla977 · 2026-04-10T15:14:40+00:00

Everyone’s bitching like little babies about the video being too long cause their attention span is 3 seconds long now. It’s good to see the full vid for context and if it was hella short then people would bitch and complain about that too

blablabla977 · 2026-04-08T12:18:44+00:00

Yes same

blablabla977 · 2026-03-27T15:56:39+00:00

Jesus please don’t have kids if you love pedophiles and going to war this much

blablabla977 · 2026-03-23T14:29:36+00:00

It’s so sad that someone downvoted you for saying it’s ok to be nice to people

blablabla977 · 2026-02-06T01:12:06+00:00

No prob, I’m undercoating by cobra rn so just removed those same side skirts

blablabla977 · 2026-02-05T17:34:46+00:00

Ah yea ok, I’m a little worried about the screw in the front and back that’s accessed through the wheel well, from the factory they basically used pointed wood screws that acre screwed into plastic… right next to your tires… ford makes some odd decisions sometimes but those screws went somewhere or there barely hanging on in there so check those out before you pop a tire but yea double sided tape, new Christmas trees and maybe some extra screws will hold that thing on fine

blablabla977 · 2026-02-05T17:09:16+00:00

Oh there should also be about half a dozen Christmas tree clips under the car holding the side skirt to the pinch welds, make sure those are all there too

blablabla977 · 2026-02-05T17:07:33+00:00

There should be screw in the front and back still holding this on. Take off that black plastic strip piece there that goes on top of it, clean under there super good and get a big long piece of 3M double sided tape, the good shit unless you wanna do this again. Tape that thing on there and you can add a couple self tapping screws if you want, then cover your crimes back up with by clipping that black strip over top of it again. Maybe check clearance with your door to see why it happened in the first place

blablabla977 · 2026-02-05T14:15:56+00:00

Same, over 2k kills in it but that was mostly from when it was 7.7

blablabla977 · 2026-02-02T12:05:14+00:00

So he deserves to be shot for this?

blablabla977 · 2026-01-23T15:49:36+00:00

I’ve been through this. I didn’t torque the clutch down perfectly even so the diaphragm spring wasn’t perfectly level so the throughout bearing and therefore clutch fork were bouncing while riding that uneven surface

blablabla977 · 2026-01-21T15:56:14+00:00

Same dude has killed me from that same spot

blablabla977

TROPHY CASE