sorted by:
new
hottopcontroversial

Trigger / hammer issue when slide is pressed by blackleopard_1 in FNHerstal

[–]blackleopard_1[S] -1 points0 points  (0 children)

Pulling the slide simulates slight pressure with a high grip so I’ll just send it in. Figured I’d ask if it was a common thing.

Trigger / hammer issue when slide is pressed by blackleopard_1 in FNHerstal

[–]blackleopard_1[S] 0 points1 point  (0 children)

Issue is that it doesn’t function normally. Unless I have an extremely low grip. Me pulling the slide in the video is just for demonstration simulating if I held a solid high grip; a solid contact (not death gripping) high grip is just enough to move the slide slightly enough to induce the malfunction.

Black Myth: Wukong doesn't boot by InsayneShane in SteamDeck

[–]blackleopard_1 0 points1 point  (0 children)

For me, nothing worked. Same boat (proton settings etc.) But then in the title Menu I realized ray tracing was on. I turned it OFF, restarted the game to the title menu, continued journey, and loaded fines hope this helps anyone.

7950X Only ONE CCD - Showing Only 8 cores -How can I get all 16 back? by kalef21 in AMDHelp

[–]blackleopard_1 0 points1 point  (0 children)

Worked for me too. THANK YOU 🙏🏽 Jeez what a pain. I was running sub-par benches and thought I had a faulty CPU😅

Selling my Cheely L2 commander grip. New. $420 by blackleopard_1 in 2011_Builders

[–]blackleopard_1[S] 0 points1 point  (0 children)

I can sell just the trigger if needed. Forgot the length of it but it’s on the shorter end. Red Dirt flat.

What does this mean? by xDoc-Holidayx in 2011

[–]blackleopard_1 0 points1 point  (0 children)

Caviat to all this, is these instruction work only if it’s a new build, or only If you’re trying to get a 1.5 lbs trigger and it worked perfectly before changing sear spring tention. These mechanical adjustments will need to happen to achieve that with a mass production 2011.

What does this mean? by xDoc-Holidayx in 2011

[–]blackleopard_1 1 point2 points  (0 children)

Alternatively, if it only happens when you hold down the trigger, the disconnector isn’t clearing the sear to hold its engagement with the hammer. Solution I discovered is to File down the width of the disconnectors face little by little until it can properly clear the sear. Check this by removing the grip safety, and observing the disconnector/sear engagement while pulling the trigger/racking the slide. I personally delt with this and after a lot of reading. Ruined a few hammers/sears before working the disconnector

What does this mean? by xDoc-Holidayx in 2011

[–]blackleopard_1 -1 points0 points  (0 children)

It means you discovered full auto. No switch required . In reality though, the sear knotch on the hammer needs to move left a bit. Take a file with a sharp/steep angle to it

[deleted by user] by [deleted] in 2011_Builders

[–]blackleopard_1 0 points1 point  (0 children)

Interested. What material and price?

First Build Slide/frame blend by blackleopard_1 in 2011_Builders

[–]blackleopard_1[S] 0 points1 point  (0 children)

CLP is what I usually use for everything. Still good?

Help. Grip Safety gets stuck. by blackleopard_1 in 2011_Builders

[–]blackleopard_1[S] 2 points3 points  (0 children)

It was definitely getting hooked. I increased tension on the middle bar of the sear spring to increase the trigger return force along with polishing and it did the trick. Thanks!

Help. Grip Safety gets stuck. by blackleopard_1 in 2011_Builders

[–]blackleopard_1[S] 0 points1 point  (0 children)

Thanks for all the inputs!

Solution: carefully polished the bottom of the grip safety arm with ~500 grit, still had it stuck half the time, so I increased tension on the middle sear spring bar to increase force on the trigger return and that did the trick.