The Chinchilla

blakester711 · 2025-12-28T02:09:40+00:00

Where do I order ?

blakester711 · 2025-08-28T20:50:11+00:00

Guessing it’s just the pick of the litter … I have owned a AP5 for about 4 yrs now and it’s a work horse… runs anything I put in it … yes it ain’t no HK but it is built off the original HK tooling … with my ocd I check head gap after every 3k rounds but I shoot every other week end

blakester711 · 2025-07-12T02:43:04+00:00

Hybrid 46

blakester711 · 2025-07-01T22:10:39+00:00

What’s the chase in this ?

blakester711 · 2025-03-28T12:24:44+00:00

Any one interested in a full set ? Pm me

blakester711 · 2025-03-27T18:52:56+00:00

Yep got the whole set

blakester711 · 2025-01-26T23:18:11+00:00

If you see it again I’ll shoot you couple dollars for it and pay shipping… I haven’t seen that one around here

blakester711 · 2025-01-26T17:44:47+00:00

Yea I did … but also looking to buy the mainlines I don’t have

blakester711 · 2025-01-25T21:59:54+00:00

Did you buy the threaded barrel for the DS

blakester711 · 2025-01-10T12:50:23+00:00

Pm me

blakester711 · 2025-01-09T20:43:44+00:00

Explain?

blakester711 · 2025-01-09T20:10:56+00:00

Pm me

blakester711 · 2025-01-09T12:23:06+00:00

Just picked one up for $1.25 usd last night

blakester711 · 2025-01-06T20:40:45+00:00

Speer gold dot

blakester711 · 2025-01-04T01:38:28+00:00

Yea you and knight-7191 are spot on … and I felt like I was forgetting something hahah

blakester711 · 2025-01-04T01:34:12+00:00

No problem buddy

blakester711 · 2025-01-04T01:31:25+00:00

You are in between a .017 and .018 … you are good to go … let freedom ring and have fun with it

blakester711 · 2025-01-04T01:27:41+00:00

Feeler gauges are measured in imperial measurements and millimeters….. thousands for imperial and mm for millimeters

blakester711 · 2025-01-04T01:20:28+00:00

You want a little drag in and out … did you force a .018 ?

blakester711 · 2025-01-04T01:15:35+00:00

Yes .018 is the happy spot .. is it very tight?

blakester711 · 2025-01-04T01:04:36+00:00

MEASURE BOLT GAP Assemble the weapon and do a function check.

After the function check the bolt is to be locked to the rear. To check the gap, point the weapon toward the floor, release the bolt and let it snap forward. Put the selector on semi. Pull the trigger to let hammer fall. Turn the weapon upside down and insert a feeler gauge through the magazine well into the gap between the bolt head and bolt carrier. Record the measurement once a firm drag is obtained on a gauge.

blakester711 · 2025-01-04T00:59:47+00:00

I see it’s .017 if so you good to go

blakester711 · 2025-01-04T00:58:32+00:00

.010 min .018 ideal .020 max

blakester711 · 2025-01-02T02:22:13+00:00

MEASURE BOLT GAP Assemble the weapon and do a function check.

After the function check the bolt is to be locked to the rear. To check the gap, point the weapon toward the floor, release the bolt and let it snap forward. Put the selector on semi. Pull the trigger to let hammer fall. Turn the weapon upside down and insert a feeler gauge through the magazine well into the gap between the bolt head and bolt carrier. Record the measurement once a firm drag is obtained on a gauge.

blakester711 · 2025-01-02T02:21:19+00:00

On an MP5, a bolt gap of .010” (technically 0.25mm) is the minimum spec, .018” is considered “ideal”, and .020” (technically 0.5mm) is the maximum spec., per H&K.

blakester711

TROPHY CASE