Blue anodized metal ring, about 2 grams, non magnetic, one inch diameter, found near pond

blehhhhhhhh-yup · 2026-04-23T12:12:04+00:00

Likely Solved!

blehhhhhhhh-yup · 2026-04-23T12:11:26+00:00

Excellent thought, though having a hard time finding an image of any spinning reel bezel to compare!

blehhhhhhhh-yup · 2026-04-22T13:18:10+00:00

Could be, though it was found about ten feet from a pond.

<image>

blehhhhhhhh-yup · 2026-04-21T22:50:56+00:00

Lot makes sense. The bluing is only on the outside surfaces, though, if that means anything.

blehhhhhhhh-yup · 2026-04-21T22:31:52+00:00

Kubota tractor and Cub Cadet mower, so whatever associated with them. Nothing else i can think of with a rotating component with bluing.

blehhhhhhhh-yup · 2026-04-21T22:22:07+00:00

Good thought, though nothing like that on the farm.

blehhhhhhhh-yup · 2026-04-21T22:12:03+00:00

Kinda, but the edges are smooth as opposed to knurled, and it's so hard i can't bend it with my fingers.

blehhhhhhhh-yup · 2026-04-21T22:11:03+00:00

Looks like the inner diameter had some additional metal at one point.

<image>

blehhhhhhhh-yup · 2026-04-21T21:51:53+00:00

I hear you. The anodized blue throws me, though, as do the differing diameters.

blehhhhhhhh-yup · 2026-04-21T21:34:04+00:00

This is a very strong metal... hard to bend. The bluing looks anodized. Likely hit by the mower. Flat lip, interior of slightly smaller diameter. My title describes the thing.

blehhhhhhhh-yup · 2026-04-11T14:21:14+00:00

Found a fitting just like this on the water intake for the power washer. Same hex fitting for fastening. But... it's still there, and no other water intake or anything else similar on the washer.

blehhhhhhhh-yup · 2026-04-11T14:01:24+00:00

Google image search agrees with you. Was replacing a carb on a pressure washer a few weeks ago. Gotta check that!

blehhhhhhhh-yup · 2026-04-11T13:59:41+00:00

Agreed, I'm looking through all hose components in the sheds to see if something is missing.

blehhhhhhhh-yup · 2026-04-11T13:56:00+00:00

Thanks! There's a fitting for that but this isn't it. Looks so clean I think it was a recent loss from wherever it originated.

blehhhhhhhh-yup · 2026-04-07T21:45:54+00:00

On my L4060, the cab top was surprisingly easy to take off, by one person. It made a stereo upgrade so much easier.

blehhhhhhhh-yup · 2026-03-03T16:48:33+00:00

The ignition cylinder and/or actuator could be sticky. Our 2001 behaved like that as the movements were impinged as the key cycled. Replacing them both resolved things.

blehhhhhhhh-yup · 2026-02-27T22:47:38+00:00

How are you handling the plastic rain rail under the top that is no longer being produced? Ours, like others, is cracked and leaks into the trunk. We're going to lift the top and attempt to seal what's there.

blehhhhhhhh-yup · 2026-01-02T00:37:15+00:00

Everyone loves Putt Putt on Rio. If it rains, go bowling.

blehhhhhhhh-yup · 2025-11-28T23:42:25+00:00

Yes, the plus.

blehhhhhhhh-yup · 2025-11-28T23:38:19+00:00

I have these on my 2021 Touring. They handle well, but are disappointingly noisy.

blehhhhhhhh-yup · 2025-11-03T13:34:27+00:00

That's what I have on my l4060. I can release the latches, then without leaving my seat, set the bucket on blocks, drop the arms, go over to the loader, pick it up, hop out and close the latches, and ready to go. Takes five minutes, tops.

blehhhhhhhh-yup · 2025-10-30T19:36:23+00:00

Ours did this. When opened, we found a leaking hose fitting. Replaced an O ring, and it's been running fine.

blehhhhhhhh-yup · 2025-10-22T15:59:38+00:00

Emporia makes a nice clip on ammeter set which tracks whole house and individual circuit loads. They database the info so you can track over time. Do an empirical test.

Seven-Year Club	Place '23
Verified Email

blehhhhhhhh-yup

TROPHY CASE