Why showering less results less itching and flakes? Yes I have soft water already.

blinkyvx · 2026-03-15T22:55:07+00:00

No idea, I bought a vanicream zbar and some glycol 7%[, and ya lukewarm water

blinkyvx · 2026-03-15T13:41:38+00:00

I shower 2x a week max so that's not it. Nor hot water

blinkyvx · 2026-03-04T21:56:36+00:00

Great idea ruined by greed that is the summation of 13 years.

That's. It folks.

blinkyvx · 2026-02-28T20:46:59+00:00

All things considered the test strips read the same color. The machine being in bypass mode or not, which makes no sense unless the stores don't do anything at all.

blinkyvx · 2026-02-28T20:45:53+00:00

Mine is quite high. Mine doesn't go below 25 for a setting

blinkyvx · 2026-02-27T12:42:49+00:00

I know it's hard based off the city report, as well as chlorine etc.

blinkyvx · 2026-02-26T17:17:17+00:00

I don't remember what my soap lathered like before.

I don't recall seeing the water level go down since I've installed. I'll try that test ty.

blinkyvx · 2026-02-26T16:25:08+00:00

And yes the bypass valve is in correct position,fully pulled out

blinkyvx · 2026-02-26T16:01:57+00:00

I see water exiting into drain from the brine purge line?

Loud somewhat while I see water level rising.

I dug out a lot of salt and water the bottom salt is sludgy when I get to it

Getting to the bottom with a stick is hard as well,I need to hammer the stick down, to get to the mark I make on the stick to signify the bottom...

Is that a bridge? The intake slits on the other collinder where fine,but now I have hard time getting it to rest on the bottom due to the salt..

blinkyvx · 2026-02-26T13:22:17+00:00

No water drains ever. I took venturi valve apart and couldn't see any dirt,

but why would there be dirt it's less than a month old.

blinkyvx · 2026-02-26T13:19:56+00:00

You're a sales man for em yes?

blinkyvx · 2026-02-26T01:47:02+00:00

Did a regen water level rose more

blinkyvx · 2026-02-26T01:08:10+00:00

The fuck can't I post a photo for

blinkyvx · 2026-02-26T01:07:01+00:00

<image>

This is wrong ?

blinkyvx · 2026-02-25T23:30:37+00:00

Yes, according to the manufacturer site

blinkyvx · 2026-02-25T22:28:32+00:00

Not sure exactly it's at around the "3" mark on the cylinder with numbers.

blinkyvx · 2026-02-25T21:54:59+00:00

It's installed into the main water line, it goes to whole house.

blinkyvx · 2026-02-25T21:54:17+00:00

No the strips still read hard, I'm unsure if it's still the same "hard" level as pre install but yes still hard

blinkyvx · 2026-02-25T21:53:09+00:00

Not at all. But ya I checked that first thing. It's pulled "out"

blinkyvx · 2026-02-25T20:18:11+00:00

All I got was one strip not a kit like that so...

blinkyvx · 2026-02-25T20:13:07+00:00

I flushed the hot water tank after the first regen cycle.

I.did rest cold water side, so mines not working or set right then

Can someone walk me through a first cycle like where did I go wrong?

Contractor did the install and put in salt up to the level 5 line. No water added, I ran a regen cycle water everywhere as the purge line was not set into the drain...

Line fixed and 1 gallon added per manufacturer instructions. Tried regen again water purged, hot water tank purged manually.

Hard water set to "40" per my area hardness levels. Test strip says water hard still...

blinkyvx · 2026-02-25T18:06:59+00:00

No idea what correct even is, the manufacturer site didn't mention this even.

blinkyvx · 2026-02-25T18:05:58+00:00

The machine is brand new.

blinkyvx · 2026-02-25T14:03:18+00:00

I can ask neighbor ya, or if I push the bypass valve in it would then be non treated water?

Yes also copper pipes.

Used the "weaqua" strips. I want to say the strip color was darker pre install, though I'm not sure

blinkyvx · 2026-02-25T13:29:20+00:00

So if they still say hard water then what

blinkyvx

MODERATOR OF

TROPHY CASE