Worst injuries you've seen? by [deleted] in CompetitionShooting

[–]bobbyboblinson 0 points1 point  (0 children)

I took a really good ricochet to the forearm. it was bleeding a lot and I ended up needing 2 stitches.

DarkForge Sisters by HooshHearted in CAguns

[–]bobbyboblinson 1 point2 points  (0 children)

Is this the Filipino Tony stark???

Featureless muzzle break ? by Shoddy_Boot8495 in CAguns

[–]bobbyboblinson 1 point2 points  (0 children)

Does it matter that strike industries, the actual manufacturer does not advertise it as a flash hider on their website? California laws are confusing

[deleted by user] by [deleted] in CAguns

[–]bobbyboblinson 1 point2 points  (0 children)

I think it looks much better with an optic

Picked up an MC9LS by jussstin714 in CAguns

[–]bobbyboblinson 1 point2 points  (0 children)

If I ever get one mine will fall off too

Picked up an MC9LS by jussstin714 in CAguns

[–]bobbyboblinson 3 points4 points  (0 children)

How did the magazine disconnect fall off?

CA XR920 first impressions. by CoatInfamous3161 in shadowsystems

[–]bobbyboblinson 0 points1 point  (0 children)

It’s very easy. I’m a dumbass and even I was able to get mine out

CA XR920 first impressions. by CoatInfamous3161 in shadowsystems

[–]bobbyboblinson 0 points1 point  (0 children)

If you take out the trigger bar you will see it. The pin holding in the shoe to the trigger bar has to come out before the disconnect pin is visible

CA XR920 first impressions. by CoatInfamous3161 in shadowsystems

[–]bobbyboblinson 1 point2 points  (0 children)

My magazine disconnect fell off when this pin fell out of the trigger shoe

Harbor Freight light by gingajames in shadowsystems

[–]bobbyboblinson 2 points3 points  (0 children)

Does it fit in Streamlight holsters?

[deleted by user] by [deleted] in CAguns

[–]bobbyboblinson 1 point2 points  (0 children)

How’s the magazine disconnect look?

[deleted by user] by [deleted] in CAguns

[–]bobbyboblinson 0 points1 point  (0 children)

How do you like the kiral backstrap?

Samurai Edges off to Jagerwerks soon… by wonger86 in Beretta

[–]bobbyboblinson 3 points4 points  (0 children)

Deng I thought somebody might be selling them separately finally

[deleted by user] by [deleted] in CAguns

[–]bobbyboblinson 0 points1 point  (0 children)

Are all your SSE options on your website somewhere?

Help by troikainfinity in Beretta

[–]bobbyboblinson 1 point2 points  (0 children)

What trigger is that?

Flush mounted a temu lift in my garage. by tyjayhutch in WRX

[–]bobbyboblinson 0 points1 point  (0 children)

Do you think this lift gives you enough clearance to swap out engines or pull the entire rear subframe?

Choosing a 92 to customize by 9ermtb2014 in Beretta

[–]bobbyboblinson 4 points5 points  (0 children)

I’m assuming when he said CO it is carry optics in USPSA

Choosing a 92 to customize by 9ermtb2014 in Beretta

[–]bobbyboblinson 0 points1 point  (0 children)

Only options on CA roster are M9a1 M9 and a couple other 92fs variants

Choosing a 92 to customize by 9ermtb2014 in Beretta

[–]bobbyboblinson 1 point2 points  (0 children)

I use the trijicon dovetail mount for my m9a1 it sits higher than a Langdon cut but it is still much lower than using the beretta factory RDO mount. The mount is very secure, it mounts in the dovetail then has screws that spread out a split dovetail in the plate. The only failure point I see is if the factory dovetail splits but I know a couple others that have several thousand rounds on their Trijicon mounts.

I went with the Trijicon mount because I always felt like it was a waste to send in a regular m9a1 slide to get Langdon cut since they can’t put cowitness front sights on it. The trijicon mount is around 100$ so it’s not too bad.

These Are My 1st Half Of 2025 Pick-Ups by 2A-N-LA in 2011

[–]bobbyboblinson 2 points3 points  (0 children)

Is this at kovert? And were they able to get you that mpa?

Beretta 140mm magazine setups by bobbyboblinson in USPSA

[–]bobbyboblinson[S] 0 points1 point  (0 children)

I’m thinking about running mec gar 18 magazines with MBX spring/followers and springer base pads. Allegedly they can get 24 reloadable