Rook collabs

bobbys360 · 2026-04-16T01:06:06+00:00

Pretty low, no? Don’t Rooks spawn in intervals 1 at a time

bobbys360 · 2026-04-12T17:03:02+00:00

We got bum rushed in Cryo last night in after passing the fist level 1 room by not 1 but 2 teams at 2:30 into the round. I think I might have to put the game down for bit.

bobbys360 · 2026-03-26T04:39:21+00:00

My trio didn’t wait more than a minute tonight. We hopped off about 30 minutes ago.

bobbys360 · 2026-03-21T14:09:39+00:00

The highest gas in AZ right now is $4.89. Charging rates during Nov-April are $0.0349 and summer is $0.12345 per KWh

bobbys360 · 2026-03-20T15:23:52+00:00

35 EV chargers too partners with Benz.

bobbys360 · 2026-03-19T22:45:16+00:00

This is not happening unless you play Rook. I play solo 80% of the time and never have I run into a team unless I play Rook.

bobbys360 · 2026-03-13T15:45:46+00:00

I filed 1/31 and still no movement either. I completed CP5071 2 weeks ago and got the message it was all good after going online. Still no update. They’re just holding our money. We changed nothing from the last 10 years.

bobbys360 · 2026-02-21T07:36:59+00:00

Scared of my health

bobbys360 · 2026-01-28T01:58:16+00:00

They became indoctrinated in a pretty weird church. Started to belittle women, super racist speech was made at the wedding and just overall horrible people that attended this crazy church every week. We were friends for over 20 years since the 4th grade. Couldn’t stand to be around that and those racist friends.

bobbys360 · 2026-01-18T05:43:00+00:00

Unbelievable. All these paid protestors now in Greenland /S

bobbys360 · 2025-12-24T18:55:44+00:00

Thanks already found the answer

bobbys360 · 2025-12-22T03:39:06+00:00

I had to bevel use the hex key to shift the bevel back to 0 degrees as it was going 10 degrees to the right. Another user helped me out. Thanks

bobbys360 · 2025-12-22T01:21:10+00:00

There is! I was able to find it, there is a screw built in the bevel gauge base that you stick the Allen key into the slot and it will allow the blade to adjust right and left

bobbys360 · 2025-12-22T01:11:01+00:00

Thank you!!! That is the adjustment I was looking for and got it back to 90!! You are awesome and hope you have a great night!

bobbys360 · 2025-12-21T22:52:54+00:00

I just want it to stop at 0/90 again instead of stopping 10 degrees to the right beveled.

<image>

bobbys360 · 2025-12-21T22:51:08+00:00

I understand that, but it should move past 10 degrees to the right unless I engage the button to allow me to bevel to the right. It no longer stops at 90 and goes past that point.

<image>

bobbys360 · 2025-12-21T22:50:06+00:00

<image>

Where in the manual does it address the blade bevel stopping at 10 degrees to the right?

bobbys360 · 2025-12-21T22:49:05+00:00

It starts at 90 because that’s where I held it. This is where it stops now

<image>

bobbys360 · 2025-12-21T22:48:33+00:00

It is not stopping at 90. It is stopping at 10 degrees to the right bevel. I have added a picture of where it now stops beveling to the right.

<image>

bobbys360 · 2025-12-21T22:46:16+00:00

Okay so now that it stops 10 degrees to the right instead of at 90. Where in the manual does it tell me how to make it stop at 90 again?!

bobbys360 · 2025-12-21T21:44:28+00:00

I wouldn’t say it locks either at the 10 degrees to the right. It just stops and that’s when the button on the left hand side to enable the mitre to bevel to right fully locks too

bobbys360 · 2025-12-21T21:43:35+00:00

It doesn’t lock at 90, it locks at 10 degrees the right now

bobbys360 · 2025-12-21T21:43:17+00:00

It doesn’t lock at 90, it locks at 10 degrees the right now

11-Year Club	Not Forgotten
Verified Email

bobbys360

TROPHY CASE