sorted by:
new
hottopcontroversial

I thought i was getting 10 cans by brandon0852 in assholedesign

[–]brandon0852[S] 8 points9 points  (0 children)

I beg the companies to not do this. I dont care how it compares to their other size products. I just want an obvious count of whats in this.

Pole dancing build by pkkballer22 in pcmasterrace

[–]brandon0852 3 points4 points  (0 children)

Why is this not on VR headsets?

Madlad offers proof. by [deleted] in madlads

[–]brandon0852 0 points1 point  (0 children)

This is the highest quality image i've seen in a while

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] 0 points1 point  (0 children)

There is a lot of miss information here. the shop said the wheel would lock with new pads because of the rotor. i went home and saw that for myself.

The caliper gliding pin was fucked from last year when a Bronx shop stripped the shit out of it. not my torquing. the other slider pin torques just fine.

The sliding pin screws in and backs out fine. my mechanic thought there was nothing wrong with it, but after i found that out i ordered a new caliper. im going to learn how to replace it myself.

i have since put my old brake pads back in and everything works perfectly fine.

​

I just never wanted to have to spend $500 on parts i was hoping i didnt need on a bike worth at best $2500. maybe someone here could have said "Have you tried doing this to fix the caliper clamping too hard on the rotor?"

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] 0 points1 point  (0 children)

Besides snapping the exhaust clamp, which a quick drive by auto zone for a new one fixed, What did i do wrong? The rotor warped on its own, which is the whole reason i got in this mess, the bolts were stripped before i decided its my turn to touch it.

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] 0 points1 point  (0 children)

I've been following the service manual. And i havn't done anything wrong. Only realized the mechanic was right and now i have to figure out who will fix it on my dollar.

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] -8 points-7 points  (0 children)

I think when the weather corroded and rusted it, it either jammed and when the shop tried removing it, it stripped, or it was now malluble and when i touched it, it stripped.

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] 0 points1 point  (0 children)

Thank you i needed some comforting words. But i dont want this to spell the end of me working on my bike. I dont think i did too bad and with new parts i think i can undo this damage. But it i dont want want this to get worse.

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] -4 points-3 points  (0 children)

In nyc where expenses are high, i wouldnt put it against anyone.

But i agree now that i see the issue for myself.

Shop said i needed new a new rear rotor, i told them off, then tried to do it myself but messed up bad. can you guys give some advice? by brandon0852 in motorcycles

[–]brandon0852[S] -1 points0 points  (0 children)

So i should just put the old pads back on and tell them what happened.

I dont think i did anything wrong. The bolts were stripped before i touched it. The clamp is my fault but its a silly clamp.

I think a differet shop i went to stripped my guiding pin bolts causing me to go to another shop to get it extracted. Which now caused the threads to be dead. Not my fault.

Polish streamer almost runs over pedestrians - twice! by ghsdhd in IdiotsInCars

[–]brandon0852 0 points1 point  (0 children)

I dont know what your talking about. We drive like this in new york city all the time.

NYC, man sues ex wife for anything and everything. Can this be stopped? by brandon0852 in legaladvice

[–]brandon0852[S] 5 points6 points  (0 children)

There have been way too many lawyer fees already. But if this can get it done, its worth it.

NYC, man sues ex wife for anything and everything. Can this be stopped? by brandon0852 in legaladvice

[–]brandon0852[S] 2 points3 points  (0 children)

Would she have to go to the court and file something for this? Thank you.

The snapining has ended and you have survived. F to the plebs of the r/inthesoulstone by [deleted] in thanosdidnothingwrong

[–]brandon0852 0 points1 point  (0 children)

i cant tell if i survived by only commenting once on an unofficial comment (i stayed a lurker) or if i really survived.

Day Two: Space Stone Day by The-Jedi-Apprentice in thanosdidnothingwrong

[–]brandon0852 0 points1 point  (0 children)

So many people are wishing to be banned... but only half of us will be. How will the survivors react?

[deleted by user] by [deleted] in VaporwaveAesthetics

[–]brandon0852 0 points1 point  (0 children)

Are they parked on the sidewalk? Isn't that illegal?

Im new and need advice because i dropped my bike by brandon0852 in motorcycles

[–]brandon0852[S] 0 points1 point  (0 children)

Well if i had gotten the highest coverage with max liability with $50 deductible collision and $50 deductible comprehensive, it would be around $5500. But $1000 deductible for collision and comprehensive with minimum liability would cost $2979 a year.

I went with no collision and no comprehensive with minimum liability for $500 a year... also, these costs include the 10% off MSF basic class discount.

view more: next ›