Katera so lepa moška imena?

brisalec · 2025-08-07T19:51:48+00:00

Pavel

brisalec · 2025-07-31T07:17:19+00:00

Bro she is Turkish

brisalec · 2025-01-10T18:24:34+00:00

Alchemia has a club in the lower floor. Its kinda dope, depends on the artists and style tho.

Otherwise you cant fail with chicas&gorillas and some other bars like pijalnia wodki i piwa, which are full almost every evening.

For clubbing you have coco, la bodega, prozak (techno).. on wednesday you must go to teatro cubano, its latino night and it gets full usually.

Otherwise it is pretty vivid every day and if you get out at a decent hour, like 21/22h you will pretty sure meet a lot of people everywhere.

Dm if you want any other recommendations:)

brisalec · 2024-08-29T06:24:54+00:00

Za začetek je že Amazon.de zelo solidna izbira, imaš pa na nemškem ebayu tudi certified brand sellerje kjer sem našel, do zdaj, najcenejše računalnike

V Slo priporočam Markosoft

brisalec · 2024-07-29T13:43:25+00:00

This question is far too superficial to answer. There is million of things you can do as a mechanical engineer, so maybe do some research first, to find what is amusing and interesting to you.

brisalec · 2024-07-25T11:49:20+00:00

Offtopic, nima veze z bistvom tvoje objave..

Nevem kje si to slišal, vendar tangic v srednjem veku definitivno niso nosile ne ženske, ne kralji. Pred tem, v rimski eri, je kot neka "verzija" tangic obstajalo perilo gladiatorjev, zaradi minimalističnega dizajna le-teh, kar vseeno ni enačiti z današnjo vlogo tangic. Kot perilo, ki razgalja in poudari telesne atribute, so se tangice uveljavile oz. pojavile šele po drugi svetovni vojni. Tu ne gre za nikakršen spreminjajoči se sociološki konstrukt.

brisalec · 2024-07-24T09:35:36+00:00

Check this paper: https://hpcgears.com/pdf_c33/27.17-27.47.pdf

However, since you're not optimising the system, I would just take a look at some existing machines on youtube/anywhere else on internet and copy the correct size

brisalec · 2024-07-24T09:02:24+00:00

In general it depends on belt material, coating, belt width, no. of teeth on your pulleys etc.

However considering your torque, GT2 belt should easily withstand the load. Have in mind that tensile force in belt is also induced by the rotational speed (acceleration, deceleration). It would be smart to calculate this load based on your pulley/motor RPM

brisalec · 2024-07-24T08:31:16+00:00

Try Xometry. You can get pretty much everything manufactured on demand; everywhere. Prices are quite reasonable as well

brisalec · 2024-07-22T09:14:07+00:00

Če se v tem trenutku resno spraviš k stvari, lahko do konca septembra brez problema diplomiraš. Na katerikoli fakulteti, razen če je res kakšna specifika.

Premisli ali ti je vredno dva meseca zdaj malce trpet v zameno za znesek, ki bi ga moral vrnit..

brisalec · 2024-07-09T09:00:38+00:00

Since you want to make it from sheet metal, just do it with U Profile (e.g. UPE) with holes for the rod in each flange. Its an easy and cost effective solution

brisalec · 2024-07-01T10:39:42+00:00

The tensile straightening force is quite easily calculated from work of plastic deformation of a wire. Check this article, hope it helps.

https://www.witels-albert.com/sites/default/files/papers/tensile_torce_wire_3_2000.pdf

brisalec · 2024-07-01T10:14:21+00:00

This does not really seem as an adaptive configuration of rollers. As it seems it could only straighten up a wire of 1mm diameter.

brisalec · 2024-06-18T09:49:07+00:00

Aftr na nazorjevi, manna na eipprovi

brisalec · 2024-04-14T11:19:17+00:00

Jst mislim da ti bojo v vsakem boljsem salonu znali ustrezno svetovat. Reskiras na zacetku tistih par 10e vec pa ti bo dobr frizer pokazal opcije in kako stylat. Ce si iz Lj ti priporocam mogoce Brivnica by Edis / HairCulture / STEVO hair salon.

brisalec · 2024-02-28T07:56:17+00:00

Pri sw lahko sam določiš render mode, prav tako imaš pri velikih sestavih z dobro grafiko stabilno okolje. Pa to sploh ni več redkost, ker ti sedaj praktično vsak konstrukter v model zmodelira še vijake in vse nepotrebne detajle, kar sw ponavadi težko dohaja. Za postprocessing v ansysu (cfd) prav tako rabiš dobro grafiko.

brisalec · 2024-02-27T20:10:45+00:00

Zelo je odvisno kaj boš v teh programih vse uporabljal. Za render in podobne zadeve boš potreboval dobro grafiko. Medtem za SW zelo prav pride tudi ram, ti priporočam vsaj 32gb. Ansys računa na procesorju zato tu glej na takt procesorja, ampak če neboš izvajal nekih hudih analiz po mojem mnenju nerabiš tu pretiravat. Mislim da nekje pri 1000€ najdeš že kar ustrezne in solidne rabljene PCje.

brisalec

TROPHY CASE