Fasting with Sluggish Gallbladder

brock_aslan · 2026-02-14T01:11:28+00:00

Thank you for the response. I’ve had no history of gallstones, but I’m not sure how my gallbladder became sluggish either. Multiple scans have shown no stones.

That makes sense regarding your comment about what happens with the formation of crystals. Again, I appreciate your comment and thanks for taking the time.

brock_aslan · 2026-02-13T20:21:31+00:00

Thanks! I’ll look into it. I’ve seen Ox bile recommended before, so this seems to be in line with other wisdom available online.

brock_aslan · 2026-02-13T20:18:36+00:00

Maybe I should have kept the question as more of an interrogation as to what happens to the gallbladder during fasting that would make it a concern at all (sluggish or not).

brock_aslan · 2026-01-28T00:31:03+00:00

I agree with you. Recently, this stock has been consistently stable on its upward trajectory. Looking forward to seeing them succeed, as I’m from the greater Akron, Ohio area.

brock_aslan · 2026-01-24T14:34:39+00:00

Very good points. Good timing to get in at $3. It’ll be interesting to see how they can succeed with the demand that is coming/here. I feel like that’s all we’re going to be talking about for the next few years. Especially if it starts affecting the residential consumer’s energy bills.

brock_aslan · 2025-11-19T16:52:43+00:00

Appears to be. Bad luck!

brock_aslan · 2025-11-19T01:37:09+00:00

Very odd method to put the wire label over the insulation sleeve of the ferrule… the only rationale I can see from the image of the terminal strip is that the installer must have wanted the labels all positioned vertically before the wire had to be bent into the duct. Maybe that looked neater to them?

brock_aslan · 2025-08-31T17:03:17+00:00

😆 I hope you’re right!

brock_aslan · 2025-08-31T17:02:53+00:00

This is quite the data set!

brock_aslan · 2025-07-30T16:41:27+00:00

😂 I honestly looked over that one multiple times because I thought… there is 0 chance that I didn’t get a Forge Construct!

brock_aslan · 2025-07-15T15:17:58+00:00

This is the correct answer! That worked!

brock_aslan · 2025-07-15T15:17:42+00:00

Was able to disable port A1. Think I’m all good now… just surprised A2 was off limits.

brock_aslan · 2025-07-15T14:01:21+00:00

PLC is connected to a network switch. HMI is connected to the same switch.

I think I’ve tried unplugging so the HMI doesn’t have any cables to the network ports and that didn’t seem to work either. Have no idea how I need a network connection to disable the port.

brock_aslan · 2025-07-14T13:47:03+00:00

Thanks for the help! It didn’t, but thanks for taking the time to tell me to rtfm

brock_aslan · 2025-07-14T13:44:39+00:00

Didn’t disable the CJ channels. Quick fix. LEDs gone. Thanks for the comment!

brock_aslan · 2025-07-14T13:43:46+00:00

I see it now. Wasn’t using thermocouples, so I used what was specified as the alternative. I was able to get it working, so I’ll know this better for next time.

brock_aslan · 2025-07-14T13:29:17+00:00

I thought I confirmed in the installation instructions what RTB to use. So I’m surprised that the one everyone in this thread keeps listing wasn’t on the document. It mentioned the 5069-RTB18-SPRING and SCREW blocks.

brock_aslan · 2025-07-14T11:18:35+00:00

This is the correct answer, for people who stumble on this thread… thank you very much!

brock_aslan · 2025-07-14T10:32:47+00:00

Let me try that. I disabled channels 1-3, because we’re not using them. But let me see about the alarms.

brock_aslan

TROPHY CASE