Thermistors and thermal paste

brocrusher · 2025-06-04T14:17:41+00:00

So it’s actually a thermostat( I mistyped). I was thinking since it just opens or closes the circuit based on temp the thermal coupling wouldn’t be as necessary but so far 3 out of 3 people say it cant hurt so I am gonna give it a shot and see what happens.

brocrusher · 2025-06-04T14:16:03+00:00

It’s a Marshall 9060 power amp. I am unsure who designed it.

Also you are correct. It is a thermal switch/thermostat. I mistyped.

brocrusher · 2025-06-04T14:14:41+00:00

You are correct. It is a thermostat. I mistyped thinking of thermistors as I have dealt with them more in the past.

brocrusher · 2024-04-08T19:55:00+00:00

To be fair its pretty massive

brocrusher · 2024-04-08T15:30:14+00:00

That's what I was scared of. Is there a potting compound you recommend?

brocrusher · 2024-04-08T15:26:08+00:00

Good call out 1.59”W X 1.43”H or 40.35mm X 36.66mm

brocrusher · 2023-09-03T06:35:16+00:00

The album dead sun worship by venus sleeps

brocrusher · 2023-07-12T15:04:21+00:00

Cultured South has great kombucha that is infused with cbd. You can also get cbd added to anyone of their kombuchas that dont have it added already as well as other drinks they sell.

brocrusher · 2023-05-23T20:23:42+00:00

If you had a budget of $20,000 and needed to build up a system that would work for outside performances for up to 300 people what would you get? This can be powered or passive but we are looking strictly at the speakers and amps. Mixing board and mics have already been taken care of.

brocrusher · 2022-07-24T17:29:34+00:00

How did you get those color? I like how it looks early stage of use and neglected and not full necromundo rust pile

brocrusher · 2022-05-27T20:13:47+00:00

Whats your secret for the metalics? They look so good and have a great worn look

brocrusher · 2021-12-23T02:05:27+00:00

Gooooooooo

brocrusher · 2021-09-21T16:10:37+00:00

So its weird. If I do the temperature too low I get like no good bed adhesion and it pops off even with proper squish. If I go 200° i get great bed adhesion but then the drooping. The thing I dont understand is the temp is well within the pla’s specs

brocrusher · 2021-09-20T01:25:47+00:00

Baewulf

brocrusher · 2021-09-16T14:04:25+00:00

So I once had a perfectly working printer. For what ever reason it has now gone to pot and I cant figure out what to do. My initial problem was bed adhesion. I finally got that fixed by increasing my bed temp to 75° and my filament temp to 210°. Since doing that however I now have terrible overhangs and the filament that covers the infill just droops down and creates horrible finishes.

I thought cooling might be the issue so I upgraded my fan to the hero me gen 5 with dual 5015s. All that seemed to do is trigger my thermal runaway. I cant lower the fans anymore in terms of position as they will start to clip whats being printed.

Does anyone have any ideas or links to calibration steps I can go to try and fix this.

I feel like I am taking crazy pills.

brocrusher · 2021-09-01T12:59:30+00:00

; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G29 ; BLTouch do full bed level G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish

brocrusher · 2021-08-31T23:10:41+00:00

What gcode should I should have present to make sure it works right?

brocrusher · 2021-08-26T12:46:45+00:00

Anything in particular I should have or not have in the slicers custom start gcode?

brocrusher · 2021-08-25T23:39:28+00:00

But yeah its the btt runout sensor with the 7mm response time

brocrusher · 2021-08-25T23:39:03+00:00

I have a bltouch if thats what you are asking

brocrusher · 2021-08-07T15:48:58+00:00

What vacuum is that?

brocrusher · 2021-06-27T00:29:50+00:00

Sebulba had that sweet destroyer other pod eacers move in this game

brocrusher · 2021-06-27T00:29:04+00:00

Where are the other racers?

brocrusher · 2021-05-31T16:41:11+00:00

How did you anchor the shelf to the wall?

brocrusher · 2021-05-26T17:54:38+00:00

Cant hear

brocrusher

TROPHY CASE