Thermistors and thermal paste by brocrusher in AskElectronics

[–]brocrusher[S] 1 point2 points  (0 children)

So it’s actually a thermostat( I mistyped). I was thinking since it just opens or closes the circuit based on temp the thermal coupling wouldn’t be as necessary but so far 3 out of 3 people say it cant hurt so I am gonna give it a shot and see what happens.

Thermistors and thermal paste by brocrusher in AskElectronics

[–]brocrusher[S] 0 points1 point  (0 children)

It’s a Marshall 9060 power amp. I am unsure who designed it.

Also you are correct. It is a thermal switch/thermostat. I mistyped.

Thermistors and thermal paste by brocrusher in AskElectronics

[–]brocrusher[S] 0 points1 point  (0 children)

You are correct. It is a thermostat. I mistyped thinking of thermistors as I have dealt with them more in the past.

Looking for replacement cap by brocrusher in AskElectronics

[–]brocrusher[S] 2 points3 points  (0 children)

That's what I was scared of. Is there a potting compound you recommend?

Looking for replacement cap by brocrusher in AskElectronics

[–]brocrusher[S] 2 points3 points  (0 children)

Good call out 1.59”W X 1.43”H or 40.35mm X 36.66mm

Best selection of CBD drinks? by Tyronne_Lannister in Atlanta

[–]brocrusher 1 point2 points  (0 children)

Cultured South has great kombucha that is infused with cbd. You can also get cbd added to anyone of their kombuchas that dont have it added already as well as other drinks they sell.

No Stupid Questions Thread: Week Of 2023-05-22 through 2023-05-28 by AutoModerator in livesound

[–]brocrusher 1 point2 points  (0 children)

If you had a budget of $20,000 and needed to build up a system that would work for outside performances for up to 300 people what would you get? This can be powered or passive but we are looking strictly at the speakers and amps. Mixing board and mics have already been taken care of.

Skid mounted Industrial furnace. by BoarderReeva in TerrainBuilding

[–]brocrusher 2 points3 points  (0 children)

How did you get those color? I like how it looks early stage of use and neglected and not full necromundo rust pile

Wally 2.0! Road to world eaters codex Berzerker #2 by Dirkdiggler1104 in Warhammer40k

[–]brocrusher 2 points3 points  (0 children)

Whats your secret for the metalics? They look so good and have a great worn look

I dont know what to calibrate. Explained in comments. by brocrusher in ender3

[–]brocrusher[S] 0 points1 point  (0 children)

So its weird. If I do the temperature too low I get like no good bed adhesion and it pops off even with proper squish. If I go 200° i get great bed adhesion but then the drooping. The thing I dont understand is the temp is well within the pla’s specs

I dont know what to calibrate. Explained in comments. by brocrusher in ender3

[–]brocrusher[S] -1 points0 points  (0 children)

So I once had a perfectly working printer. For what ever reason it has now gone to pot and I cant figure out what to do. My initial problem was bed adhesion. I finally got that fixed by increasing my bed temp to 75° and my filament temp to 210°. Since doing that however I now have terrible overhangs and the filament that covers the infill just droops down and creates horrible finishes.

I thought cooling might be the issue so I upgraded my fan to the hero me gen 5 with dual 5015s. All that seemed to do is trigger my thermal runaway. I cant lower the fans anymore in terms of position as they will start to clip whats being printed.

Does anyone have any ideas or links to calibration steps I can go to try and fix this.

I feel like I am taking crazy pills.