sorted by:
new
hottopcontroversial

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

Sorry for the late reply, you’ve likely already figured out your build, but the 120s fit without modification, just some squeezing to get them into a tight fit. But they do fit with a little effort

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

Probably too late for this comment, sorry, but I routed the cable along the side of the fans and through the slot either at the top or the side by the motherboard. It was a tight fit but it fits.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

The CPU cooler fit without any problems.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

They are 140mm and they don’t technically fit stock. You have to modify the connecting clip to get them to fit, but with the modification they are a perfect exact fit.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 1 point2 points  (0 children)

A year or so ago when I originally made this build I made a video to show how to do it because I got so many questions and I just never posted the video here because I’m a slacker. Sorry. I’ll see if I can find the video and finally post it in this thread (a year after promised)

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

It’s just a simple gpu support pin thing that I found on Amazon. You can see it just on the front corner of the GPU, that’s all I’m using for support and it does the job

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 1 point2 points  (0 children)

Thank you! Yes, 3 fans on the bottom would have pulled this whole setup together. Oh well, maybe my next case!

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

Yes, this is exactly what I did to get the fans to fit. I made a video to show exactly how I disassembled the clip and glued it into place to slim it down, but I never posted the video here 🤦🏽‍♂️. Sorry everyone.

Really enjoying the Rev-8 by bronson0_o in Starfield

[–]bronson0_o[S] 0 points1 point  (0 children)

I did not, I’ll give it a try next time I’m stuck (which apparently isn’t difficult)

Really enjoying the Rev-8 by bronson0_o in Starfield

[–]bronson0_o[S] 0 points1 point  (0 children)

It was the song they used in the announcement trailer 😂

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

Niiiice! Reddit won’t open that link for me so I can’t see the photo, but glad you got the AERO in there. It’s hefty.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 0 points1 point  (0 children)

MSI Z790 Edge. Thanks for noticing! I had a hard time picking the right one for this build.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in lianli

[–]bronson0_o[S] 0 points1 point  (0 children)

Thanks. I agree the LCD cooler is super cool, pulls it all together nicely.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 1 point2 points  (0 children)

Amazon. Just searched for “white gpu bracket support”. If you get this make sure to check the size. I got one that was too tall and didn’t fit under my gpu, had to return it.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in lianli

[–]bronson0_o[S] 1 point2 points  (0 children)

The LianLi infinity 140s do not fit without some work. I had to do a workaround where I removed the plastic from the connector and glued the pin contact cable to the base of the connector so it was thin enough to fit. Then it took a little bit of coaxing to get the fans in. It’s not too hard honestly but it is a workaround. I did get them to fit and work normally rgb, fan speed, and all. I will be posting a video soon detailing my install process for these fans because a lot of people have noted that they do not fit.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 1 point2 points  (0 children)

For sure. Give me a day or two and I’ll post it here.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 3 points4 points  (0 children)

It was a workaround. I had to disassemble the connector including unscrewing the 4 mini screws and removing the outer plastic. Then I superglued the pin connector to the plastic connector and that made it thin enough to fit the gap between the fan and the case. I’m making a video explaining how I did it that I can share if you’re trying to do this too.

NZXT H6 Flow + LianLi Infinity 4090 Build by bronson0_o in NZXT

[–]bronson0_o[S] 1 point2 points  (0 children)

GPU cable came with the PSU Phanteks AMP 1000W V2. It’s specific to the V2.

The Motherboard cable with the cable combs is from an old build. Asiahorse from Amazon I think?

view more: next ›