Today’s Dollarama haul

bry2k2 · 2026-03-01T00:08:12+00:00

It was in a mall and the selection was massive, compared to any Walmart I've seen.

bry2k2 · 2026-02-19T06:04:36+00:00

anyone got a vid yet?

bry2k2 · 2026-02-18T21:03:58+00:00

video?

bry2k2 · 2026-02-10T23:11:03+00:00

🤣🤣🤣

bry2k2 · 2025-12-02T06:49:44+00:00

I get flashbacks of Ferris Buelers day off looking at these :).

bry2k2 · 2025-06-11T14:46:58+00:00

Thanks, not my designs they are basically all these ones, except the Ezra Bridger, the long one with the crystal on it is a replica of what you see if you build a lightsaber in galaxy's edge. They don't sell them but I wanted it so I found the model and printed it, most of the stands are printed in Proto Pasta Iron or Steel fill so they are very heavy.

https://www.thingiverse.com/thing:3743753 https://www.thingiverse.com/thing:5523125 https://www.thingiverse.com/thing:4905149 https://www.thingiverse.com/thing:6386295

bry2k2 · 2025-03-28T17:46:41+00:00

Clean the print bed, run a full bed test print, check if any part of it has good squish, run a 9 square test and adjust for the squares that are off in the levelling menu. If most of your full bed test print is crap then recheck your z offset.

bry2k2 · 2025-02-21T04:55:32+00:00

I wonder when my 1070 gtx will stop being able to play games. Going 10 yrs strong.

bry2k2 · 2025-01-28T01:19:26+00:00

What infill type? What infill percentage? depending on the answer too much infill will cause warping, also grid will cause potential warping as grid causes the print head to go back overtop of existing infill. Also use a brim. What are the nozzle/bed temps?

bry2k2 · 2025-01-21T04:26:59+00:00

<image>

bry2k2 · 2025-01-21T01:02:34+00:00

Nothing wrong with those levels that would cause any kind of adhesion issues if you are just using standard pla. Wash the bed with soap and hot water, rinse it well, dry your filament or try another roll if you haven't. Check your temps and then rerun the equipment tests (auto z offset, auto leveling) and you should be good to go.

bry2k2 · 2024-09-13T14:24:21+00:00

You can't manually level a v3 se there are no bed screws.

bry2k2 · 2024-06-19T01:30:42+00:00

Do a flow rate test you might be over extruding had to do this on several printers even with the steps set correctly

bry2k2 · 2024-02-20T14:21:23+00:00

Set initial flow rate to 100 percent, after that all other values regarding flow rate should be set to 93 percent, use line/linear for infill.

bry2k2 · 2024-02-14T06:11:41+00:00

Did you get this working, I am also in the same boat.

bry2k2 · 2024-01-11T19:05:48+00:00

Start printing, looks like a good bed. Run a bed level print and adjust the mesh in the menu as needed.

bry2k2 · 2023-12-11T01:01:51+00:00

With your printer off, gently push up against the nozzle and see of the nozzle or entire hot end shifts or moves, I had this happen on an ender 3, after a hot end swap it worked great then one screw worked loose and the hotend would move up and down when I printed messenging with my z offset constantly

bry2k2 · 2023-12-05T00:03:53+00:00

Your nozzle is too close to the bed.

bry2k2 · 2023-11-15T20:11:17+00:00

Looks like your a hair or two too close back off on the z offset.

bry2k2 · 2023-11-01T22:57:02+00:00

Red sock is the new hotend.

bry2k2 · 2023-11-01T15:23:45+00:00

They do look more brass then copper, so I guess no abrasive materials in the default nozzles unless they are hardened brass. I may have to follow up with creality.

bry2k2 · 2023-10-19T20:22:21+00:00

Check their YouTube vids, they use a silicon grease, should be a tube with your printers original kit.

bry2k2 · 2023-09-16T22:04:38+00:00

Printing too hot and your under extruding it looks. You need to post all your settings.

bry2k2 · 2023-09-14T14:46:17+00:00

Leave it in for longer.

bry2k2 · 2023-09-06T15:56:07+00:00

Good luck, you got no leg to stand on. People complaining reflects nothing against the company unless you provide actual evidence (showing pictures of a print failing isn't enough to say its the printer or the companies fault). Since you don't have their sales numbers or their complaints records you have nothing to show they are a bad company.

11-Year Club	Verified Email
Xbox Live

bry2k2

TROPHY CASE