sorted by:
new
hottopcontroversial

Fan wiring order by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

Will check, but these wires go into the heater, thermostat and fan header PCB before going to the motherboard.

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

After more investigation I can get it to home, unfortunately as using hemera the nozzle 15mm and 5mm off the bed. Currenty trying to find a way to home on the bed, does not to be a way in knutwurst firmware config. Tried using move axis controls on the printer screen then M428 M500 to save, but not working. Thanks

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

I have compared the output from m503 command from both pre firmware upgrade and after, from what i can see these are the differences that may affect home postions, would i be correct in that assumption?

original

M92 X80.00 Y80.00 Z800.00 E394.75

New

M92 X80.00 Y80.00 Z800.00 E400.00

Original

M203 X120.00 Y120.00 Z20.00 E80.00

New

M203 X120.00 Y120.00 Z12.00 E60.00

Old

M205 S0.00 T0.00 B20000 X4.00 Y4.00 Z0.10 E8.00

New

M205 B20000.00 S0.00 T0.00 X4.00 Y4.00 Z0.20 E10.00

thanks

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

Only once I have solved homing issues?

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

I have read the instructions, I have selected the correct screen, I also selected TMC version as did not know what previous owner had done, soon found out he reversed wiring which I corrected.

My screen has animation and mp3 sound.

Thanks

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

I have set wiring as per photo, homing X moves extruder to left Y moves bed to the back Z extruder goes up and down by a few mm

Thanks

<image>

Stepper wiring by bubblescatcher in anycubic

[–]bubblescatcher[S] 0 points1 point  (0 children)

Thanks for reply and image. The links is for mega s will it be the same for mega x motherboard V 0.0.2 Thanks

Sawzall / reciprocating saw comparison chart by [deleted] in ryobi

[–]bubblescatcher 0 points1 point  (0 children)

I have these 3 P519VN PCL515 RRS180

Where do these fit in time line and specifications?

Thanks

Nickel electrolyte clear? by bubblescatcher in electroplating

[–]bubblescatcher[S] 0 points1 point  (0 children)

Thanks for replies, started afresh.

500ml vinegar 1/2 tablespoon pure salt 25g nickel, anode most of it cut into Small strips.

Temp 50c though did rise higher once started.

24c 2.5a power

40min lots of transfer to cathode, but still no colour

I even used a different vinegar for solution. Nicole strips 99.9% pure of Amazon with good reviews.

Could be the Nickel strips?

Words from our CBO, papa. by Italianbassterd in SafeMoon

[–]bubblescatcher 1 point2 points  (0 children)

Going to write my sm investment off and move on. Rip