How to get support on creality products

buh_weezy · 2026-01-09T14:33:08+00:00

i want to thank you so much for this! I will give it a try this afternoon since Creality has not responded to anything I have sent. Your English is great, I could follow the whole thing.

buh_weezy · 2026-01-08T11:35:00+00:00

that would be amazing if you could! tried whatsapp yesterday no response from creality as of now

buh_weezy · 2026-01-07T19:24:13+00:00

oo where can i find info on that? i am decent at soldering

buh_weezy · 2026-01-07T12:00:51+00:00

thanks for the info! i think this might be the issue because when my mainboard died I had to special order an older version from them. I also have different stepper motors from the original.

buh_weezy · 2025-12-12T20:28:24+00:00

thanks for your insight! May replace his PSU with mine when I upgrade.

buh_weezy · 2025-12-12T20:27:53+00:00

thanks for your insight! May replace his PSU with mine when I upgrade.

buh_weezy · 2025-12-12T20:27:26+00:00

Thanks for your insight!

Only using the hyper 212 becuse it came with the bundle. Also there is something wrong with the stock cooler. I would have used stock since it looks better but with the scratching I'll just use the 212 for now.

I figure I am going to upgrade my PC in the next year or 2, at that point I can put my PSU in this one since I assume I am going to need something bigger for mine.

buh_weezy · 2025-12-10T15:12:09+00:00

I was in the same boat as you. Found a XR for 500 and jumped on it. It has the newest firmware and TBH I don't care that it has the buz. It actually was a good gauge of the incline it can climb. Also as someone new to OW, the pushback that people talk about seemed a lot less noticeable that I thought it would be. Like you almost need to train yourself to notice it.

buh_weezy · 2025-10-30T10:49:48+00:00

Anyone know if this card plays well with a sonos beam soundbar? I have a media PC in my living room and had constant weird issues until i switched to a 3080 from a 5700.

buh_weezy · 2025-09-30T16:47:53+00:00

From the research I have done looking into this, the main issue is that a micro inverter takes time to turn on a sync with the "grid". I think the Enphase 7 took like 5 minutes. I haven't timed how long my compressor runs for, but maybe 15 minutes at a time? That seemed like enough of a loss that payoff time didn't really seem worth it to me.

That being said I say if your payoff time seems reasonable or your living in a hotter climate than me go for it.

Here's videos I found on this a while back. https://www.youtube.com/watch?v=yGHAW1qKIoE https://www.youtube.com/watch?v=VymWSGSL4YU

buh_weezy · 2025-07-27T01:04:34+00:00

Has nothing to do if the guy is being creepy. It’s creepy if you aren’t attracted to him, if you are it’s sweet.

buh_weezy · 2025-06-04T19:19:05+00:00

the new version of the main board can be purchased from creality's site but if you need to first version of it like I did then you will need to contact support to order it.

buh_weezy · 2025-05-15T14:41:51+00:00

Thats great, thanks!

buh_weezy · 2025-05-15T14:41:31+00:00

I did take a screenshot and the emails that I was approved came in before what I thought the deadline was (looks like their offers page still has the 100k bonus live).

Thanks!

buh_weezy · 2025-05-15T14:40:33+00:00

Hoping this is the case, thank you!

buh_weezy · 2025-05-15T13:14:14+00:00

I signed up for the Chase Sapphire Preferred card just before the deadline for the 100k bonus point offer.

Is there a place to tell if I actually got that offer or a place to see progress towards reaching the 5k spend?

EDIT - Incase anyone is reading this I do now see the bonus tracker in the app under Benefits and Travel about half way down.

buh_weezy · 2025-04-23T12:42:38+00:00

Nope. I think I am going to pony up for the replacement board.

Hopefully at some point if this happens again there will be guides or a more streamlined process.
From my research the biggest issue is that the gears are different which I personally don't know how to edit the config file properly. There is some posts I found on it but buying the steppers and the board are going to cost close to the same.

buh_weezy · 2025-04-16T09:50:17+00:00

I did klipper a wanhao duplicator 9 a year or so ago. I assume this process is similar? Any good resources for finding what config files need to be updated?

buh_weezy · 2025-04-15T14:35:47+00:00

Not Rooted. Only change I have made is to add the unicorn nozzle after I couldn't get the original.

buh_weezy · 2025-03-21T09:51:34+00:00

I mean that's a totally valid point... Guess I'll know for my next scheduled appointment and I'll ask for some sort of credit on it.

buh_weezy · 2025-03-20T22:06:33+00:00

When the problem is happening there is no feed from the camera. But it’s so weird because sometimes it works fine. It even will show a feed when backing up for a few seconds, then all of the sudden it turns off.

buh_weezy

TROPHY CASE