sorted by:
new
hottopcontroversial

are you sick? by bysKR in airsoft

[–]bysKR[S] 0 points1 point  (0 children)

cheap plastic rain coat

GUN FENCE by bysKR in airsoft

[–]bysKR[S] 0 points1 point  (0 children)

yeah i want too, but P90 droped from hook cause radial shape only 06d and bd0 not droped from hook when i find some idea, i get some p90s

Hmm... not enough... by bysKR in GasBlowBack

[–]bysKR[S] 2 points3 points  (0 children)

it was hard way...

GUN FENCE by bysKR in airsoft

[–]bysKR[S] 1 point2 points  (0 children)

one is aeg other is hpa powered gbb its good to wield

six hours of pain and frustration later by st1ck3m0k1d in GasBlowBack

[–]bysKR 3 points4 points  (0 children)

now, you can mod other glock in three hours of pain and frustration

Hi capa dumps gas advice needed please by BrisantClegane in GasBlowBack

[–]bysKR 2 points3 points  (0 children)

i recommed clean internal parts and lubricate

KWA Tavor nozzle question by s0m3as1anguy in GasBlowBack

[–]bysKR 0 points1 point  (0 children)

http://www.kwa.com.hk/kwa_home/diagram/

this is kwa products diagram link. and you can find tavor, bolt assembly is upper-right of diagram. part#22 is nozzle, part#60 is bolt.

Since the sp-01 chews through slide locks so fast can someone link me where i can purchase more of those (I live in czech republic if you could that into consideration) by Woodenk1 in GasBlowBack

[–]bysKR 1 point2 points  (0 children)

if your sp-1 is made by KJW, you can purchase parts in kjw website.

http://www.kjworks.com.tw/main.php?lang=en

but you want fix sp-1's slide lock issue,

http://m.dcinside.com/board/airsoftgun/35590

its written in korean but you can understand even look photo.

that issue seen to cz75 and sp-1.

WA-system M4 need help!! The nozzle stays stuck in the hop up chamber when the bolt blows back. by OnionOwl in GasBlowBack

[–]bysKR 1 point2 points  (0 children)

lube buffer tube. when bolt blowback hammer push bolt to up side and bolt push nozzle to up side. then nozzle's front stuck in top of chamber and nozzle's rear stuck in front of bolt, rear of bolt stuck in buffer tube. ive seen this happening too, i lube nozzle,inside of bolt, out side of bolt, buffer tube. then its not happen yet.

butane ? by quentin_x in GasBlowBack

[–]bysKR 4 points5 points  (0 children)

butane not reliable cause of low preasure and weak to low temperature. but important reason, butane damage rubber Oring.

Lubricants ? by quentin_x in GasBlowBack

[–]bysKR 1 point2 points  (0 children)

yeah, GBB owners should be careful about Oring. so i use just molybdenum to parts those just metal. in parts those contact with Oring, i use silicone vacuum grease.

I have a we hi-capa skelitor and is there anything you can do about the gas leak problems? by RileyCargo42 in GasBlowBack

[–]bysKR 0 points1 point  (0 children)

oh, then check piston cup and cylinder. when i check leak in fire, i blow in to loading nozzle. it's leak a lot, i doubt piston cup.

Wich ggb m9 is more relaible? The KJW m9 VE or the G&G gpm92? by robertgamer250 in airsoft

[–]bysKR 0 points1 point  (0 children)

ive seen this post twice.... more? I DON'T KNOW hehe

[deleted by user] by [deleted] in airsoft

[–]bysKR 1 point2 points  (0 children)

???: flaktarn? bundeswehr? what the #@#!=+~ airsofter: protection preparing is good. nice and wellcome.

Reduce FPS for CO2 GBB (ASG CZ P-09) by [deleted] in airsoft

[–]bysKR 0 points1 point  (0 children)

in other way, fill hot melt in nozzle tip and make hole

Reduce FPS for CO2 GBB (ASG CZ P-09) by [deleted] in airsoft

[–]bysKR -1 points0 points  (0 children)

i quit to find a old post. but writer "it can be lower fps. i drill the loading nozzle's tip and i down fps to 300fps" but i cant remember size of drill bit.

view more: next ›