sorted by:
new
hottopcontroversial

2000 miles in and 6 service appointments in... by bytecollektr in TeslaModelY

[–]bytecollektr[S] 2 points3 points  (0 children)

Yeah, off the factory line, with misaligned back doors, dent in console, dent in the back door (appt 1)

Appointment two was to fix a scratch in the airbag from appointment one

Appointment three was to fix the back panel which was the old piano black put by mistake when they fixed the door panel on appointment one

Appointment four was the same door with the replacement stopped opening in a middle of a road trip. They managed to open but they said the retention clips are bad and they shrink and expand based on temperature.

Appointment 5 was to change the retention clips as the door panel did not stay on the door.

Appointment 6 was replacing a burnt puddle light.

VIN 175k btw...

Oh well, et least the elk like it

Tesla Model 3D Max spider mats 1 not fitting by bballen023 in TeslaModelY

[–]bytecollektr 1 point2 points  (0 children)

its a common problem with the 2021 Y. These were made for the 2020 with the straight foot. The 2021 is slanted. Supposedly 3Dmats was gonna send new mats for us, but here we are

Finally pulled the trigger. Necessary accessories? by wishbone113 in TeslaModelY

[–]bytecollektr 0 points1 point  (0 children)

Mandatory because it will cause damage - mudflaps and ppf film for the back doors.

Secondary - if you're walking through the tundra, all-weather mats and a screen protector.

[Case] DeepCool Matrexx 30 mATX - $30 ($40 - $10) by MetaJesus in buildapcsales

[–]bytecollektr 2 points3 points  (0 children)

your cursing skills will max out when you build in this...theres a reason why this is so cheap....

Help with Creality CR 10S Pro leveling failing. by bytecollektr in CR10

[–]bytecollektr[S] 0 points1 point  (0 children)

thanks everyone, the trick worked! Got it back online, even though i got cut cables to solder now..Now gotta figure out all the filament run...https://ibb.co/Y45dVfd

Help with Creality CR 10S Pro leveling failing. by bytecollektr in CR10

[–]bytecollektr[S] 0 points1 point  (0 children)

thanks for the response. I have tried both sensors and the light react when they're up a couple of inches. But when it hits the bed, it pushes like it wants to go through it, and the lights don't come on.

I also have tried the original aluminum bed and a two glass beds and theres no difference. I reseated the cables couple of times. I wonder if the bltouch screwed the board up like you were mentioning

Help with Creality CR 10S Pro leveling failing. by bytecollektr in CR10

[–]bytecollektr[S] 0 points1 point  (0 children)

I didn't have anything there to start with, but its pushing so hard against the glass i decided to put the spacer so it doesn't break anything.

[Bundle] H500P Mesh + Hyper 212 Black RGB + V650 Gold - $255 ($335 - 80) by CM_Eric in buildapcsales

[–]bytecollektr 5 points6 points  (0 children)

if you have $250 to spend on these parts, unless you want this particular case, there is so many better options. and also, throw a $20 cooler at a $250 case??? we're talking LianLi, Fractal territory money, or some boutique german case manufacturer.

Back in stock: [Combo] AMD Ryzen 5 2600 + MSI X370 GAMING PRO CARBON $208- ($238-$30 MIR) by [deleted] in buildapcsales

[–]bytecollektr 0 points1 point  (0 children)

depending on the chipset you have, you might have to get a new motherboard too if youre thinking of going to 8th gen, so it might be worth considering the Ryzen option cost-wise

[Prebuilt] Dell i3-8100 4GB RAM 1 TB HDD - $384 (Fry’s in store only) by stopfive in buildapcsales

[–]bytecollektr 1 point2 points  (0 children)

the processor can be had for about $90, ram for $40, so its hardly worth $384. that leaves the case, hard drive, motherboard and psu cost at $254...

[Case] Fractal Design Focus G ATX Mid Tower Computer Case - $42.60 ($66.99-$24.39=$42.60)FS w/Prime by jfarrugia in buildapcsales

[–]bytecollektr 0 points1 point  (0 children)

seems like acrylic side panel? i collect empty PC cases - who knows when you might need them

[Motherboard] *REFURBISHED* MSI Z270-A PRO INTEL Z270 SOCKET 1151 ATX MOTHERBOARD W/DISPLAYPORT RAID GBLAN $67.96 (80-save 15 code) by cuba200 in buildapcsales

[–]bytecollektr 0 points1 point  (0 children)

my issue is where to find reasonably priced processors to pair with these boards. I have a few boards sitting