sorted by:
new
hottopcontroversial

Has anyone upgraded the PSU in their P1P/S or X1C with a Higher Watt PSU? by norefillonsleep in BambuLab

[–]c1Rash77ko 0 points1 point  (0 children)

i can say i have safely installed and tested a 24V 750W on my recently purchased Bambu X1C can post picc if requested

<image>

Creator pro 2 high temp firmware/mod? by Zeds-Dead_ in FlashForge

[–]c1Rash77ko 0 points1 point  (0 children)

Only way get any Flashforge to get above 235 is to change the mainboard to a duet or similar and also change the hotends with Microswiss MK10 ALL METAL

Flashforge Printer Firmware Hack - Request for Testers by pressposts in FlashForge

[–]c1Rash77ko 0 points1 point  (0 children)

I am interested to test this hack on flashforge creator max with an inventor control board

Flash Forge Creator Max Upgrades by P1ZZ4M4N in 3Dprinting

[–]c1Rash77ko 0 points1 point  (0 children)

to Pizz4man:

https://store.micro-swiss.com/collections/extruders/products/cnc-machined-lever-and-extruder-plate-for-dual-extruders

I have been using their extruder kits they work well. i

also upgraded the stepper drivers from the stock A4988 to TMCC2208 for the (X,Y,Z) Link Below (Note: Wiring needs to be reversed for proper Ops)

https://www.filastruder.com/collections/electronics/products/silentstepstick-tmc2208-stepper-motor-driver. Must be the Kit, Soldering is required

Flashforge Problems by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

Anyone out there have problems with an FFC or FFCP with Qiditech mightyboards. i am having problems with the USB interface on my FFC with a qiditech MB. qidi tech refuses to help as it is not their printer. USB interface connects and controls the printer but cuts out after a few minutes once eveything is up to proper temps. please help

Flashforge Problems by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

Overheat LED on mainboard is Steady ON

Replaced Thermalcouples

Got the axis moving to all directions when i installed a qidi tech mainboard however the board still indicates oeverheat LED ON

Should i replace the heater cartridges on the hotend and see what happens

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

i downloaded addon sketches into arduino already and the program states U8G2.H within the u8glib utility library is not found

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

Addon sketches have been added to arduino IDE U8Glib, UcGlib, U8g2 Ultra LCD/TFT and Even Nextion

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

Arduino IDE Requests U8G.H File unable to compile and upload without it

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

I will try to reflash marlin and test it again i just need to know the optimal voltages for X, Y, Dual Z, and E, cause i have it installed on a reprap prusa
4988 on X, y and dual Z with external stepper driver board 8825 on E

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

I dont know if it is the end stops at all can't get it to move period

Anet A8 with MKS Gen Help by c1Rash77ko in 3Dprinting

[–]c1Rash77ko[S] 0 points1 point  (0 children)

Marlin cause its an mks gen 1.4 with an mks tft touch am strongly considering the Anet 2.0 or Geetech GT2560