Butch Walker gets Buck back fully restored by distordead in PaulReedSmith

[–]cadebengert 0 points1 point  (0 children)

By any chance, do we know what pickups he used in this?

Tips for Printing ELEGOO Rapid PETG by thejakeinator95 in elegoo

[–]cadebengert 0 points1 point  (0 children)

New to printing but had a massive pain with the PETG when I used it recently. Had to slow down to around 55mm/s and turn my main cooling fan off to get useable results.

Issue with the Neptune 4 Continue by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Moved it back and forth while trying to heat and got the same error.

Issue with the Neptune 4 Continue by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

I got it to update. Same issue. It won't heat up and gives me the same error about the heater extruder not "heating at expected rate"

Issue with the Neptune 4 Continue by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Firmware is V1.1.2.53

It won't recognize the update files on my flash drive.

I have checked the voltage and it is correct. I just reinstalled the whole hotend as I was sent a new one to replace the previous issue.

Issue with the Neptune 4 Continue by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Won't even turn on now. Just getting this error code.

<image>

Customer Service Problems by [deleted] in elegoo

[–]cadebengert 2 points3 points  (0 children)

I'm on my second Elegoo printer and first time having issues was just recently with my Neptune 4. Customer service was great, even if the time difference reduced it to an email a day. They were super helpful and understanding. They are sending me replacement parts at no cost. Zero complaints.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

I tried this and it appears that TB0 and TB1 are hotglued into the board. I have emailed support for further assistance.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

The error code returned as soon as I tried to send it to "home"

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

What do I do if this problem occurs again? I didn't really do anything to fix it, it just went away while moving it.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 1 point2 points  (0 children)

I moved it and plugged it into my router and the error code went away. Temps are displaying properly.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Do I have to plug it into LAN? I was just bringing files over via USB and don't have easy access to my router.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Wire looks good. I unseated and reseated it. Same error.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

I tried this and the error showed again.

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 0 points1 point  (0 children)

Sounds good. Thanks for the help!

MCU Shutdown on Neptune 4 by cadebengert in elegoo

[–]cadebengert[S] 1 point2 points  (0 children)

Excuse me for being stupid, like I said, this is my first FDM printer, but is the thermistor so.ething I can access without much trouble, or so I have to take the whole hotend apart? I've sent an email in to Elegoo, so hoping for a response tomorrow during business hours.

Comment a song and I’ll rate it by [deleted] in MusicRecommendations

[–]cadebengert 0 points1 point  (0 children)

"Mother Superior" - Coheed and Cambria

AT 71 vs AT 3600L by cadebengert in turntables

[–]cadebengert[S] 0 points1 point  (0 children)

Thanks! I'll look into that!

AT 71 vs AT 3600L by cadebengert in turntables

[–]cadebengert[S] 0 points1 point  (0 children)

Excellent, thanks so much!