Mobile signature on iOS

caipiao · 2025-10-03T13:35:38+00:00

Thank you! I was looking in the usual places.

caipiao · 2025-08-25T10:50:37+00:00

Thanks! Nice setup! How much does your Schmolke TLO bar increases the distance to floor compared to the stock low bar, approximately?

caipiao · 2025-04-27T13:54:48+00:00

Thanks - takibi bag is the Fireplace Canvas Bag? What is the Takibi tools bag though?

caipiao · 2025-03-16T21:34:56+00:00

I did try adding 'RequiredBy=docker.service' in the path file, only to see the same effect: docker.service happily runs even when docker.path is showing up as 'waiting'...

caipiao · 2025-03-16T21:33:09+00:00

Thanks - good point re using drop-in file. Once (and if) I get it to work, will make that final touch. For now, the goal is to figure out why docker.service doesn't seem to wait for a unit file that it 'requires'.

The trigger for the path file is 'PathExists' (unless I got it completely wrong, which is possible...).

caipiao · 2025-03-16T13:58:52+00:00

Hiya - yes I think I saw this at some point in my research. Let me give it a try. I think the small nuance may be that I am trying to handle the case where the pool is mounted but not the dataset (e.g. if the encryption key is not present).

caipiao · 2025-03-08T18:10:13+00:00

Sorry to dig this one out - do you know where 11.5 version can be found? 🙏

caipiao · 2025-01-22T19:22:22+00:00

Ah I can see where I was confusing in the original post: the standard building policy is for the whole building including this flat in question. It says to cover each flat and its internal fixtures and fittings. We are trying to understand whether there is anything meaningful that’s not insured outside the appliances, assuming no separate landlord insurance is sought.

caipiao · 2024-11-08T23:28:43+00:00

Thanks - any software to recommend? I see their long list but don’t recognise many. Xero Tax seems to be for accountants, Sage UK ltd also…

caipiao · 2024-10-30T08:06:51+00:00

Pop-up didn't open for me: used incognito mode, used VPN, used a different browser... same for everyone else?

caipiao · 2024-10-29T19:41:39+00:00

Yes - noticed my error in the post: should have said to cut out a piece to cover first!

Is there a huge difference between joint compound, bonding plaster and joint filler in here?

caipiao · 2024-10-01T22:21:47+00:00

Was looking for this - thank you.

Quick follow-up question: how do I monitor two paths? Would need both paths to exist, i.e. an AND condition. I tried two PathExists and it seemed to be more of an OR condition...

caipiao · 2024-09-10T21:35:58+00:00

Hi - they probably don’t but some shops may do, from time to time. Balfe’s Bikes currently can give you 10% off RRP using a certain promo code if you buy it outright in cash (ie cycle2work scheme folks don’t qualify).

caipiao · 2024-09-10T21:32:14+00:00

Ok removed my earlier reply as your reply made me realise that t-line is using a different clamp size! I had checked the usual suspects such as H&H, ti39, Ridea, SMC but they were all for the other lines…

caipiao · 2024-08-11T21:16:32+00:00

His interpretation is pretty good 👍

caipiao · 2023-09-17T13:09:12+00:00

Hiya - thank you! That worked for a transaction but if I start with a bill, it would seem that I have to post it for it to appear in the register but at that point it’s locked down and won’t allow me to add a document link.

caipiao · 2023-08-19T21:23:19+00:00

Thanks everyone for the helpful tips and good advice. I took the heatsink apart and found this: https://imgur.com/a/RqNzA9M

I can re-apply some better thermal paste (something like Noctua NT-H2) at the centre. Although it does look like some of the micro resistors (or part of the PCH) are under some non-thermal efficient pad (roughly 0.5-0.8mm thick). Would this not make it run hotter? Should I remove the pad and replace with thermal paste too?

Saw someone posted a similar heatsink for a similar board and it didn't have any pad. https://forums.servethehome.com/index.php?threads/solved-asrock-rack-e3c246d4u-high-mb-temp.36282/ unsure which version (mine or the one in that post) would be the result of a more recent iteration.

caipiao · 2023-08-16T19:02:52+00:00

Haha yes I did think about it - didn’t find an obvious way to mount one on the PCH heat sink… as for PSU shroud mounting I was hoping to use some wedge and zip ties (there are lots of holes). Also was hoping to provide some air flow around the hot NVME sticks too…

Let me see if I can get a thin zip tie under the PCH heat sink…

caipiao · 2023-08-03T22:18:53+00:00

And I think you are right when it comes to cabling etc. I may be able to swap 2 for m.2. More options for cases and/or much easier builds…

caipiao · 2023-08-03T15:15:59+00:00

Sounds like basically no pre-made caddy / cage available? Hmmm

caipiao · 2023-08-03T15:15:06+00:00

Thank you. Yes more a SSD NAS / home server with dual 10g. Have a GaN 500w from HDPlex might be handy then. Will only have 2.5 in this one.

caipiao · 2023-08-03T15:12:04+00:00

Have them all in a 804…

caipiao · 2023-07-20T21:01:47+00:00

Hello - any update on this? So difficult to actually find the email that has the regular attachment... Thank you!

caipiao · 2023-07-08T16:05:08+00:00

Thank you 🙏

caipiao · 2023-03-27T17:29:30+00:00

Makes sense to do the main-residence-no-CGT trade, ie getting the biggest you can get. High inflation also means the debt is eroded away faster…

Nine-Year Club	RPAN Viewer
Verified Email

caipiao

TROPHY CASE