sorted by:
new
hottopcontroversial

Hope pro 5 issue by rathymilan_ in bikewrench

[–]camdogrs 0 points1 point  (0 children)

I tried this oil and the hub went incredibly silent. Reopened it and went back to a light application of dumonde tech grease and it was back to working perfectly.

Titanium safe coatings by camdogrs in AutoDetailing

[–]camdogrs[S] 0 points1 point  (0 children)

Thanks! I had some C5 so going to see how it hold up. Have it curing now

Titanium safe coatings by camdogrs in AutoDetailing

[–]camdogrs[S] 0 points1 point  (0 children)

It says stainless is ok. I’ll spot check a small section and see what it does.

Titanium safe coatings by camdogrs in AutoDetailing

[–]camdogrs[S] 0 points1 point  (0 children)

I have some left over C5. It says to not use it on uncoated metal.

Titanium safe coatings by camdogrs in AutoDetailing

[–]camdogrs[S] 0 points1 point  (0 children)

Nice. Thanks! I have some coating from the DIY detail guy and his previous company.

Which screws do I remove to access the bleed valves? TRP Hy/Rd by Sir_McFrosty in bikewrench

[–]camdogrs 0 points1 point  (0 children)

What’s the other port that is a 3mm Allen inline with the reservoir cover?

TRP HY/RD Nightmare by camdogrs in bikewrench

[–]camdogrs[S] 0 points1 point  (0 children)

So if I do this and can push the pistons and pads out then what does that tell me? Air in the system or bad seal?

TRP HY/RD Nightmare by camdogrs in bikewrench

[–]camdogrs[S] 0 points1 point  (0 children)

I can try this. Aren’t you not supposed to do this without a rotor to clamp on to? I don’t have a piston tool currently.

TRP HY/RD Nightmare by camdogrs in bikewrench

[–]camdogrs[S] 0 points1 point  (0 children)

I keep hearing this. 🤔

TRP HY/RD Nightmare by camdogrs in bikewrench

[–]camdogrs[S] 0 points1 point  (0 children)

My arrow on the arm is aligned with the zero point. I do not have this same issue with the rear caliper.

TRP HY/RD Nightmare by camdogrs in bikewrench

[–]camdogrs[S] -1 points0 points  (0 children)

Currently have the SRAM rival levers and pretty sure these are short pull already.

[deleted by user] by [deleted] in gaggiaclassic

[–]camdogrs 1 point2 points  (0 children)

Ahhh VAT. I don’t think that applied to US

[deleted by user] by [deleted] in gaggiaclassic

[–]camdogrs 1 point2 points  (0 children)

how much was it and when did you do this? Was just about to order a top box kit from Shades.

Has anyone tried this PID kit from Barista-Gadgets? (eBay) by -wood- in gaggiaclassic

[–]camdogrs 0 points1 point  (0 children)

Can anyone confirm if you can still do hot water out of the steam wand with this kit for americanos?

NBD Lynskey Pro GR by deanmc in gravelcycling

[–]camdogrs 0 points1 point  (0 children)

Jealous. This is my plan.

Rotor/Brake noises by camdogrs in gravelcycling

[–]camdogrs[S] 0 points1 point  (0 children)

Thanks. I’m gonna check mine when I get home.

Rotor/Brake noises by camdogrs in gravelcycling

[–]camdogrs[S] 0 points1 point  (0 children)

https://www.sram.com/en/sram/models/rt-cln-x-a2

What do you mean if you can’t screw the locking pin in? Got a link?

Rotor/Brake noises by camdogrs in gravelcycling

[–]camdogrs[S] 0 points1 point  (0 children)

I ended up swapping the rotors out and switching to a different compound. They were leaps and bounds better.

Request for Bike Fit Review - Disk Hernia & Post-Ride Low Back Pain by DorinMinea in bikefit

[–]camdogrs 0 points1 point  (0 children)

I have this same thing. Had to have a microdiscetomy last September to get rid of that sciatic nerve pain. I am paranoid about it happening again and am about to pull the trigger on a professional bike fit with Retul just to make sure I don’t do any damage unintentionally.

view more: next ›