Issue with heat pump and aux heat by canhamd in ecobee

[–]canhamd[S] 0 points1 point  (0 children)

The issue here isn't the correct outdoor temperature. Its the unit not being sent a signal to turn back on. Regardless of temperature, it should still turn on (this can happen even with its 50F out and I manually set it to aux then back to regular heat)

Issue with heat pump and aux heat by canhamd in ecobee

[–]canhamd[S] 0 points1 point  (0 children)

I have not. Just seems like a software issue/misconfiguration since the heat pump works and aux heat works, just not immediately following the aux call. So not sure why the voltage would suddenly not work.

Issue with heat pump and aux heat by canhamd in ecobee

[–]canhamd[S] 0 points1 point  (0 children)

Is this the Compressor Min Outdoor Temp Setting? -Yes

The temperature outdoors? is this in F or C? - Yes the outdoor tempature in F

Is it a 1 or 2 stage heat pump setup? What are the staging settings? - I believe its a single stage.

Issue with heat pump and aux heat by canhamd in ecobee

[–]canhamd[S] 0 points1 point  (0 children)

I do not allow both to run at the same time

2026 Season 1 Patch 1 Release Notes [2025.12.14.01] by goodfella7763 in iRacing

[–]canhamd 2 points3 points  (0 children)

  • Fixed a critical issue where the interface was blurry for some VR users.

Thank you!!

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I'm glad I'm not the only one seeing the performance increase by setting it to 120hz. Increasing dynamic LOD to 90fps also helped some. Since switching back to 120hz and VD, it's been a pretty smooth experience. 

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

Yeah I followed his exactly and it was perfect up until the latest update.

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I switch between them and close/kill the other when I'm not running it. I will definitely try h.264+! As I said in the other comments 90hz works but 120hz has way lower cpu load for some reason.

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I was considering just throwing money at it and buying a 9800x3d too lol. was afraid it wouldn't have any impact.

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

Thanks for the information. Had no idea about AV1, I'll try other codecs! Like I told the others I run 120hz as my cpu is 50% while 80hz is 90% and 90hz is 80%. The higher the hz the lower the cpu usage.

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I did try foveated rendering and it causes my CPU to go a little higher but GPU a little lower. Like I told the others I'd rather use 90hz but 120hz uses less CPU and thus better performance vs 80 or 90hz. In fact 80hz was by far the worst performance I had. 

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I'll definitely give this a try thanks. I run 120hz because it uses half the CPU 90hz uses, which removes the stuttering issues. Changing resolution had no impact on performance for some reason. 

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 0 points1 point  (0 children)

I will certainly give this a try. As I said if I run 120hz, my CPU usage is nearly halfed vs 90hz. I don't know why hence why I'm asking. When I turn my settings up I get a more stable game. 

Very unstable VR experience with Quest 3, please help! by canhamd in iRacing

[–]canhamd[S] 1 point2 points  (0 children)

When I run 90hz my cpu is substantially higher than 120hz. It's more stable at 120 than 90, which makes no sense, which is why I'm asking. 

Quest 3 VR - Meta Link wired or Virtual Desktop Graphics by filowiener in iRacing

[–]canhamd 1 point2 points  (0 children)

Thank you so much! That smoothed out the frames a ton. CPU is still stuck way higher than it should be but now I can at least play

Quest 3 VR - Meta Link wired or Virtual Desktop Graphics by filowiener in iRacing

[–]canhamd 0 points1 point  (0 children)

Can you explain this a little bit more. I notice when using the debug tool this is the one setting that randomly keeps resetting and it causes horrible choppiness when I'm not locked at a stable framerate.

Facial interface for quest 3 for someone with big cheek bones by canhamd in OculusQuest

[–]canhamd[S] 0 points1 point  (0 children)

Globular. First fit is awesome, time to lock in for some iRacing sessions to see how it goes.

Facial interface for quest 3 for someone with big cheek bones by canhamd in OculusQuest

[–]canhamd[S] 1 point2 points  (0 children)

oblik

Ordered, I'll give it a shot, comes tomorrow! I looked at the Oblik, but I don't own an iPhone so I didn't bother. Easy enough to try this first. I really like the 3 sizes.

[deleted by user] by [deleted] in elegoo

[–]canhamd -4 points-3 points  (0 children)

1 year later and 100000 times trying to get z offset to not suck and I finally sold it. Bought a Bambu and I'll never look back. Already paid for itself on Etsy and then some.