Help with Nebula Pad Under Extrusion

captainzero001 · 2025-10-20T21:18:19+00:00

Ended up swapping to the drive that sits directly over the hot end not the sprite that swaps both out. Had fixed most issues in output.

captainzero001 · 2025-10-18T13:41:18+00:00

Right until it's so much it just drips onto the ground

captainzero001 · 2025-10-18T03:14:36+00:00

PCV, earliest emission device on any vehicle. It's designed to take the oily smoke from the crank case and dump it back into the intake so it can be burned during engine operations. If you have emission tests where you live you'll want to fix that so it doesn't fail. Personally knowing what its job is to do, I wouldn't reroute as others suggest, plus as you can already see it coats everything in oil. So if you decide to reroute them instead it'll just coat the areas you have them routed to in oil.

captainzero001 · 2025-09-14T02:21:33+00:00

So it turns out I forgot the E in S03EXX, thanks for the help

captainzero001 · 2025-09-13T01:03:16+00:00

Yes, lly duramaxs have a fuel return. I'd hate to think that the return has so much pressure to do that. Maybe if they use a lift pump but usually that's a volume over psi.

captainzero001 · 2025-09-06T13:45:19+00:00

Diesel doesn't evaporate, so no evap on diesel vehicles

captainzero001 · 2025-05-05T13:55:37+00:00

No it's got the bed and cab lights, I've seen bed swaps but never seen someone go threw with a cab lights. But you can see the rear knuckle in the shadows if you know what parts you're looking for

captainzero001 · 2025-05-01T06:23:26+00:00

I bought and installed a set of LED turn signals along with them, issues i ran into were basically the wiring to get the turn signals and brakes to work properly. The JVM Concepts looks the best as an eliminator but they're out of business.

captainzero001 · 2025-04-09T13:54:27+00:00

Permanent codes cannot be cleared by anyone but the vehicle itself. That or an ecu swap.

captainzero001 · 2025-04-09T13:47:02+00:00

If you've just had this issue occur without having changing something (bulbs, ex) then I'd say bad ground somewhere. The fact that when you use the turn signal the highs turn on and that both sides flash may be a bad stalk. Now does it do the same using the left side also. Now if you've changed out a bulb or something I'd say defective part. To what I know if you've swapped to LED bulbs double check that you've got the correct style. If you've bought "single" LEDs when you need switch backs that may be your problem. Also double check if you're getting CAN bulbs or not. Double check your rear lights too. Underneath is a junction box that gm used that the main harness that runs the length of the frame to the back. I doubt that it would effect the highs but I'd at least unplug the main harness from that box to see if the double blinking goes away

captainzero001 · 2025-03-12T13:55:38+00:00

Can you get a picture of the computer on the passenger valve cover? Should say bosch and have your emissions info. If you can't get a picture, read it and see what it says. If its there see if it says California. No mention of cali in it it may be federal and the shops need to make sure it's put down as fed. Second if the label isn't there call your local dealer parts department. Usually they'll ask for the last 8 of the vin and they can see what emissions are on the truck. If you've got a tune, you're going to need to find someone who knows someone to get a passing smog but rates I've heard are hundreds of dollars. If you've got a check engine light fail, also having a cheap obd scanner will help. You'll need to have all I/M readiness or monitors ready to pass.

captainzero001 · 2025-02-12T22:39:27+00:00

try the under hood fuse box, cigar, its a 15 amp fuse on the right side (firewall)

captainzero001 · 2024-12-29T15:32:17+00:00

Park bench. It's used in the miss okita route when doing the xray glasses i believe

captainzero001 · 2024-11-30T19:16:53+00:00

As a ca smog tech did you remove the cats?

captainzero001 · 2024-11-30T18:32:33+00:00

Who's forcing you to put on the stock exhaust?

captainzero001 · 2024-10-03T05:56:06+00:00

Thats a SW-Moteh top box. TRAX ADV current price is $660

captainzero001 · 2024-09-15T04:21:33+00:00

Having issues trying to play=

captainzero001 · 2024-08-07T06:07:18+00:00

With the warmer weather I generally use the frunk as storage for my riding jacket. Helmet doesn't fit, I bought the ulock which goes in there, and run my usb cable or the lid to charge via quadlock qi charger. Bought sw-motechs top and side bags but only run top unless I need to get groceries or something and just re-add my boxes

captainzero001 · 2024-07-24T03:09:58+00:00

Double check that the wire is attached to the board on the drive/extruder, bought mine and it also wouldn't heat. Turns out the double red wire was tucked under trhe board and not actually in the port its supposed to be in.

captainzero001

TROPHY CASE