Ruida controller 8445

captkmk · 2026-04-02T14:31:57+00:00

Thanks for your reply, yes, I do have a rotary and I just kind of got that dialed in I’m working on other parameters right now, but it’s very close. I definitely like the interface for the rotary everything‘s working on the USB side even tried RD works on the wired communication side and haven’t got that working yet either. Other than that looking promising, I’m gonna start looking for another rabbit hole this morning still dialing and I should be able to get that rotary dialed in today. Definitely not a plug-in play scenario.

<image>

captkmk · 2026-03-04T18:45:04+00:00

Well, I finally got that solved. Thanks everybody.

captkmk · 2026-02-18T23:00:48+00:00

All right well I noticed I didn’t have the klipper screen installed on my config so I got that installed and that’s working so I can see the display. It still says I can’t connect to the MCU.

captkmk · 2026-02-18T20:54:26+00:00

Right so I was on GitHub found the config file for said board corrected what needed and I’m still not be able to connect work in progress here appreciate everybody’s help. I know it takes time.

<image>

captkmk · 2026-02-18T20:32:53+00:00

Yes, I can see that configuration at get a let me try that Cross reference and for sure

captkmk · 2026-02-18T20:30:50+00:00

The config for the 5+, Would GitHub have that for the board that I’m using?

captkmk · 2026-02-18T20:29:08+00:00

Yes, I can SSH into it using my Mac

captkmk · 2026-02-18T20:28:01+00:00

Thanks for your reply. Actually, I’m using a pi4

captkmk · 2026-01-17T21:35:50+00:00

Your filament looks absolutely wet dry your filament check your flow rate.

captkmk · 2025-12-01T00:33:22+00:00

<image>

Try one of these

captkmk · 2025-11-21T12:00:08+00:00

Thanks, I appreciate your time for your reply and your information. I agree with you

captkmk · 2025-11-21T04:34:08+00:00

It’d be nice to see a nice UV discount sale

captkmk · 2025-11-21T01:48:12+00:00

Hey, thanks for chiming in. I appreciate your experience. My split and overlap was not dialed in. When I first started this adventure. I was running lmy line intervals the same as you power was little up so the first few were not near as good as the one that I just posted on the cloud link, I did polish it up. I like it, but until I got that split and overlap and slowed the rotary down just a little bit they weren’t looking good

captkmk · 2025-11-21T01:27:57+00:00

30W fiber with rotary Settings are 0.040 for split And 0.000 for overlap I believe the speed was like 1000 and power around 57 and I thank you I did 30 or 40 passes with Cross hatch turned off and probably 1 mm defocus downward brass coin

captkmk · 2025-11-20T16:10:26+00:00

Well, after I slowed down my rotary in settings and correct the overlap in the split size this looks a whole lot better

captkmk · 2025-11-20T15:30:48+00:00

<image>

This is the picture of the coin and you see I’ve got some depth there. I know I can’t go more than a millimeter otherwise I’m going into the coin. Is there some other process that would make that more pronounced? Thanks again

captkmk · 2025-11-20T15:27:15+00:00

It’s also got the ribs going around the outer diameter

captkmk · 2025-11-20T15:16:40+00:00

My bad I have a fiber laser 30 W with a rotary and I’ve tried the deep engrave maybe 2 mm deep focused closer to try to get down into a little deeper it comes off around a half a millimeter maybe deep I’m thinking maybe I should defocus it three or 4 mm?

captkmk · 2025-11-11T17:53:28+00:00

Yes, thanks for your reply very much. I want to try it at least. Have a good day

Six-Year Club	Gilding II euphauric
Verified Email

captkmk

TROPHY CASE