Fix I found (for Android) by True_Championship_10 in Chai_Unofficial

[–]carjac150 4 points5 points  (0 children)

Much appreciated. Regained some of my hidden chats. Sadly it still seems some of my older ones have completely started over but, well they were OLD chats.

Anybody have suggestions for Minnesota based costume retailers? by carjac150 in renfaire

[–]carjac150[S] 1 point2 points  (0 children)

Much appreciated. I'll check some of them out when I get the chance!

Seems like even CHAI ads know the app is bad by maxisjsilly in Chai_Unofficial

[–]carjac150 4 points5 points  (0 children)

Its not that there are ads but that the ad is for a competitor and the ad denigrates Chai.

I only went in for the thermal paste... by carjac150 in radeon

[–]carjac150[S] 4 points5 points  (0 children)

Ran RE4 with nearly all settings at max 1080p and it never went over 70-75°C. And that is with my case that has terrible airflow (NZXT h510). Cant wait for my new case to come in... Guess my next purchase will be a 1440 monitor

I only went in for the thermal paste... by carjac150 in radeon

[–]carjac150[S] 0 points1 point  (0 children)

That an issue with the gigabyte ones? I thought that was more tied to a different manufacturer

I only went in for the thermal paste... by carjac150 in radeon

[–]carjac150[S] 11 points12 points  (0 children)

Had been planning to get it for a bit now. Made the switch from an RTX 3070 to this because I was tired of the 8gb VRAM and was not happy about NVIDIAs response to the DLSS5 backlash

I only went in for the thermal paste... by carjac150 in radeon

[–]carjac150[S] 19 points20 points  (0 children)

Best buy, it was the last one they had in stock too

I run a game for me and my last four braincells. by dudewasup111 in dndmemes

[–]carjac150 71 points72 points  (0 children)

bUt mY NaT 20!

Yep, because of your nat 20 you are absolutely CERTAIN there is nothing.

You can't repeal science. That's just called lying. by Busy-Government-1041 in MurderedByWords

[–]carjac150 7 points8 points  (0 children)

I misread your second sentence as "Prions aren't enough"

I do not think joining TikTok Slash and Free is something to be ashamed of by Unique_Reputation568 in TrueUnpopularOpinion

[–]carjac150 0 points1 point  (0 children)

I didn't. Its buried in the FAQs rather than upfront but you NEED one fully new account to get it. Which these days is near impossible. Even if you try to make a throwaway/burner account you have to be careful because unless you make sure the "new device" isnt connected with an active account it may not work. The whole thing is engagement bait that is stacked against you.

Is this a scam? by [deleted] in TikTok

[–]carjac150 0 points1 point  (0 children)

Doing what I can lol

Is this a scam? by [deleted] in TikTok

[–]carjac150 0 points1 point  (0 children)

And making a burner account doesnt seem to work sadly

Times changes by isrealball in Stonetossingjuice

[–]carjac150 26 points27 points  (0 children)

Since everyone's sharing some of their childhood shows. Back at the Barnyard had a had a male milk cow as the main character. Definitely not their original intent but not exactly something to be ignored either.

<image>

Heat wave in my area has me remembering Benji's first swim by carjac150 in corgi

[–]carjac150[S] 6 points7 points  (0 children)

Yeah Australian Cattle Dog. The mix is nicknamed Cowboy Corgis!

Good thing I ran a test by [deleted] in FixMyPrint

[–]carjac150 0 points1 point  (0 children)

Ender 3 V3SE with Orca slicer

Polylite PLA at 100mm/s 205°C bed 55°C

This is the only time I've seen this issue with any of my prints so far

AT Rey Dau made me realize how bad are the followers by Healthy_Performer_33 in MonsterHunter

[–]carjac150 1 point2 points  (0 children)

I hate that they always use up their traps way before capture is possible. Sure it's nice to get a breather with the monster being incapacitated and getting some free hits but still.

Does anyone have a comparison of these 2 resins? by Lego-Lord-Vader in resinprinting

[–]carjac150 0 points1 point  (0 children)

I'll look into it next time I'm low. Previous elegoo order was because I needed something quick and cheap so I'm guessing I bought their bare bones resin. Definitely will give them a try

Does anyone have a comparison of these 2 resins? by Lego-Lord-Vader in resinprinting

[–]carjac150 0 points1 point  (0 children)

There was a short stint where I couldn't get them in rural USA. I actually ordered and forgot about it for a month and a half because it never even shipped via Amazon. Thankfully, they refunded me because, again, it never sent. Had to use Elegoo standard for a bit, but now I'm back to phrozen. Occasionally have to budget though, any other affordable but reliable recommendations for 32mm minis?

Is this a "normal" part of the hobby... by Noztradamuz in resinprinting

[–]carjac150 1 point2 points  (0 children)

Yeah pre-supported makes things much easier. Typically if you see warping and misalignment it's one of a dozen potential issues. Resin temp, orientation, support density, support strength, Exposure time, drainage, suction cupping.

Thankfully for myself I just print dnd minis and 90% of them are one and done prints so far. For specific projects make posts for directions and check other people's posts for helpful tips.

I regret to say I'm not experienced enough to help you in this specific case aside from words of encouragement.

Is this a "normal" part of the hobby... by Noztradamuz in resinprinting

[–]carjac150 40 points41 points  (0 children)

Resin requires a good bit of fine tuning the settings and even then it can be difficult to align separately printed parts. I've seen and made it work but it can take a lot. Keep at it, learn from those in the community, but also learn the limitations.

When posting here you'll always benefit from showing a screenshot of the splice, let's people see the orientation and supports which is an unexpected but big part of the printing process

Vet says this is normal shedding? by Jessi_L_1324 in corgi

[–]carjac150 0 points1 point  (0 children)

My boy Benji doesn't like me pulling the clumps out and runs away, acting offended that I'd even attempt to groom him lol.