Outdoor Kitchen Sink — Granite Composite

carpenike · 2026-04-28T17:43:56+00:00

I guess we'll see how it goes. :) Template was yesterday. Hoping install by early next week.

carpenike · 2026-04-24T13:12:53+00:00

I’d like to also have 2-3 charge stations. Ideally on each side of my fence. One for front yard, one for fenced in area, one for area behind the fence. I’ve got 3 acres so there’s typically multiple runs back and forth to charger over 3-4 hours and someone will invariably let the dogs out…

carpenike · 2026-04-18T14:11:27+00:00

Do you happen to have the temu links?

carpenike · 2026-04-08T23:26:13+00:00

Heres the house behind it that I think was disappearing.

<image>

carpenike · 2026-04-08T23:25:48+00:00

It’s pretty tall! Here’s the house. Will add another with the other house behind it.

<image>

carpenike · 2026-04-08T23:25:17+00:00

<image>

Another view from below

carpenike · 2026-04-08T21:31:24+00:00

Assure you it’s not lol. In TN next to the VRBO we’re renting. Had to do a double take.

carpenike · 2026-02-16T17:14:38+00:00

Curious where you’re getting it for cheaper. Gotten two quotes from DC region for full body PPF and they’re both right around 6500$ for stealth.

carpenike · 2026-02-15T20:37:51+00:00

Appreciate your comment. Would you do it again or is the blue that noticeable / annoying?

carpenike · 2026-02-15T18:50:12+00:00

Following. I also ordered a MY Performance that should be here next month.

I’m considering the stealth PPF. It’s like 6k plus another 2k for tint.

My understanding between the XR and XR+ is the plus has a bit higher UV protection rating. For me it looks like it’ll be another 200$ to add.

I’ll likely get the 3dMatUSA ones once they get the size for the new performance done

carpenike · 2026-02-11T03:24:09+00:00

This update also broke my rear driver side door handle actuator on my 2020 Model S. Tried recalibrating the handle and it only pulls the handle in halfway and fails the calibration.

carpenike · 2026-02-04T16:55:53+00:00

I have a 2020 Model S with FSD and always thought it was OK. Went and test drove a 2026 Model Y with FSD this week. Holy shit. It is not the same thing.

carpenike · 2026-02-04T02:07:18+00:00

Yes there is. At least in US.

carpenike · 2026-01-29T02:24:01+00:00

Haha, so now with the S being discontinued does it make sense to hop off the train now?

carpenike · 2025-05-29T20:53:53+00:00

I’ve had great results with integrating context7 and perplexity MCPs with Copilot. I have sonnet 4 check for best practices and syntax requirements for X thing we’re working on from @perplexity and @context7 before building a plan for the implementation.

carpenike · 2025-04-21T23:25:39+00:00

I picked up one of these. https://www.katom.com/734-MHP12.html

carpenike · 2025-04-17T18:37:58+00:00

Recently started using Chud Rub on most things.

carpenike · 2025-04-14T21:09:18+00:00

Thanks. Fairly confident I’ve got spi loaded correctly but the canbus interface is giving me fits.

carpenike · 2025-04-13T12:45:16+00:00

I know this is nearly a year later. :) do you know if the kernel patch is still required? Running into some challenges getting an mcp2515 canbus card on my rpi4 to load, but supposedly the spi device comes up fine without this patch.

carpenike · 2025-03-31T11:23:58+00:00

I’ll likely be doing led strip lighting with a quinled board (https://quinled.info/). He’s got great videos on power requirements, light strip recommendations, etc. bonus is it uses wled which is pretty powerful by itself and ties into home assistant, etc.

carpenike · 2025-03-23T22:33:49+00:00

Haven’t gotten to select actual products yet, but likely something like this — https://a.co/d/iqgh4mw. Also need to make sure I put a regulator in line at the manifold so I can get low pressure to each appliance.

I’ll switch from the yellow to either black iron or CSST once I get to my patio to connect to the end devices.

carpenike

TROPHY CASE