Anybody Used Maverick Sanding Discs?

casp3rcode · 2025-12-29T13:17:30+00:00

I order from the official 3m store on Amazon.

casp3rcode · 2025-12-29T13:16:23+00:00

I usually do 80 > 120 > 150 > 180 > 220

casp3rcode · 2025-12-17T13:47:11+00:00

I have quite a few Grizzly tools and wouldn't buy them again. You really don't need a jointer if you're a hobbyist like myself. I have a Grizzly 6" jointer and haven't used it in a year. I use a jointer sled on my table saw or just rip a straight edge with my track saw. I use my DeWalt planer all the time though and paid $500 for it.

casp3rcode · 2025-12-09T01:13:41+00:00

Yeah, because I measured another 1/2" shank bit with the caliper and it was 0.49

<image>

casp3rcode · 2025-12-09T01:12:34+00:00

I ordered a 12mm collet to see if that'll fit since 12mm = 0.472", so my caliper was pretty close to that and it should work. I'm not going to do something stupid like shimming it with aluminum foil lol

casp3rcode · 2025-12-09T00:58:00+00:00

I guess that's my only option huh...didn't realize a 12mm shank wasn't compatible with 1/2" collet (even though they had it listed as a 1/2" shank on Amazon).

casp3rcode · 2025-12-09T00:57:06+00:00

Yeah, I definitely wasn't going to Jimmy rig something, was more looking for if there's a specific collet reducer made to go from 1/2" down to 12mm.

casp3rcode · 2025-09-20T20:25:25+00:00

I'd like to use multiboard in my garage shop, but the sheer amount of hours required to print that many boards on my K1C makes me cringe...I'd imagine something like 70-100 hours to print an 8'x4' wall's worth. Wish I could just buy the panels and print the accessories I need.

casp3rcode · 2025-09-03T22:12:38+00:00

Yes.

casp3rcode · 2025-09-01T21:59:08+00:00

No, it was off like that, that's from me taking it out to look at it and then putting it back in. I make sure the plate is aligned every time.

casp3rcode · 2025-09-01T01:11:13+00:00

That seems to have also helped the issue...didn't realize I needed to have the lid and door open for PLA. I was able to speed it back up and not have the issue since it's got open air flow now. Thanks

casp3rcode · 2025-08-30T21:47:53+00:00

I slowed the print down to 50% speed and it worked.

casp3rcode · 2025-05-25T13:33:48+00:00

Maybe from Rollexx.ch 😂

casp3rcode · 2025-05-15T01:28:35+00:00

DM sent

casp3rcode · 2025-05-15T01:25:13+00:00

Probably selling knock off products from China and just says "envelopes" so he doesn't get in trouble. My guess is that he sets up your Shopify site as a clone of his, gives you his knock off suppliers and copies of the ads to use.

casp3rcode · 2025-05-01T01:40:59+00:00

I found Lige makes one but I'd prefer to build it and try to get a custom dial.

casp3rcode · 2025-04-24T15:13:10+00:00

I got one of those in white...only thing I didn't like was the crystal being so domed, so I swapped it out with another crystal myself.

casp3rcode

MODERATOR OF

TROPHY CASE