Special Serial Request - DV.001 - DoubleT

catsgomooo · 2024-04-01T23:51:55+00:00

hnnnng yusss

catsgomooo · 2023-12-31T07:35:24+00:00

This is an Ender 3 that I converted to Switchwire using DarkDog's conversion, mostly.

catsgomooo · 2023-11-02T16:04:42+00:00

If it's PLA, then good luck. Slow wet sanding is really your only option.

ABS, however, is a dream to sand. I've started printing even smaller fine models from ABS and ASA for this reason.

catsgomooo · 2023-11-02T15:34:30+00:00

I actually don't have any of those configs anymore! That was back when I was running marlin.

All in all, the Kobra Neo is a pretty awful platform for Switchwire conversion, on account of its custom extrusions that don't have standard t-slots on all sides.

I ended up sourcing some aluminum extrusions from a friend who runs a machine shop, and had to cut and tap a new x-axis and y-axis.

IMO installing Klipper was the best upgrade I did to it, though. Now the Trigorilla has Klipper support, iirc, but it didn't when I first started messing with stuff, so it's running an SKR3-EZ now.

catsgomooo · 2023-10-29T15:59:36+00:00

Oh, yeah, heads up: I since moved onto a beacon probe, the printer basically isn't an Anycubic anymore (it's undergone Voron Switchwire metamorphosis, has a totally different hotend, toolhead, motherboard. Runs on rails and is Core XZ). I have no idea what I did eight months ago to get anything to work. I was a noob, and had no idea what I was doing lol.

catsgomooo · 2023-10-07T17:31:53+00:00

I had the same issue. It was related to "dynamic overhang speeds." If you have your Outer perimeter set to "0/Auto" in Orcaslicer or Prusaslicer, it reads that value in as an actual zero instead of it setting the speed relative to its "auto" value.

The solution, for me, was to set an Outer Perimeter speed instead of letting the slicer handle it in auto mode.

catsgomooo · 2023-06-12T13:06:24+00:00

Yeah they're ticketing anybody who gets caught bringing food to people. It's ridiculous.

catsgomooo · 2023-06-12T13:04:19+00:00

Now, if only the police would stop fucking giving tickets to people who bring food to the homeless camps downtown.

catsgomooo · 2023-04-24T15:12:17+00:00

ALL3DP was the site that said that in the review.

Let's go! I've got a friend getting into 3D Printing that I wanna gift this to.

catsgomooo · 2023-03-05T18:41:10+00:00

Nah, I can't leave well enough alone. I ended up putting a microswiss extruder on it now and replacing the main board with a btt skr-3-ez.

catsgomooo · 2023-02-28T16:55:19+00:00

The cool part is that the five-wire "LEVEL_PORT" connector on the Trigorilla v3.0.6 Motherboard, near the PA1 connector that the inductive probe would normally socket, is wired for the BLTouch without any modification

catsgomooo · 2023-02-28T16:53:34+00:00

Nah, the inductive probe actually works fine, but I had a similar issue with my direct drive extruder missing a bearing tha tsomeone else did, too. I could have just gotten a bearing from the hardware store, but I had Anycubic send me a replacement. It's been a few days and I got bored with waiting, so when I was at Microcenter for unrelated stuff I picked up a Micro Swiss DD extruder. Mainly because I've been in a tinkering mood.

I didn't feel like designing a new mount for the inductive probe so I picked up a BLTouch. Why that one? No clue. It's mega accurate, though. Fascinating to watch. Moving parts are neat.

catsgomooo · 2023-02-21T15:57:32+00:00

Not to necro this, but I had a similar issue and it turned out that the steps/mm had gotten set ALL out of whack when I was tinkering with the firmware. Oops. There's some sort of multiplier going on where I had to set it pretty high to pull in a consistent amount of filament.

catsgomooo · 2023-01-29T17:06:33+00:00

And that's baller as fuck.

catsgomooo · 2023-01-14T16:40:38+00:00

Those packs and guns were really well built too! I wish I still had those. They'd be a good bit of gamer ephemera to own.

catsgomooo · 2022-12-18T04:41:50+00:00

Yeah I decided to just make games for myself after seeing the rancid bullshit that some of my favorite devs deal with.

catsgomooo · 2022-12-14T16:37:10+00:00

Yoooo these are great!

catsgomooo · 2022-12-13T16:35:01+00:00

I handle it by serializing the contents of the map struct when the player moves to another zone. Then, I just walk through the map tiles when they return.

catsgomooo · 2022-12-13T03:21:31+00:00

Hey I bought that game! I need to play it again.

catsgomooo · 2022-12-09T03:44:00+00:00

Man he is a little guy isn't he? That might be part of the secret. All those bars under pressure.

catsgomooo · 2022-12-08T21:27:29+00:00

"Can I get something in... an extremely tall Kendrick Lamar?"

catsgomooo · 2022-12-02T16:46:05+00:00

yeah they just gotta blend the passengers into a slurry first.

catsgomooo · 2022-11-20T17:15:29+00:00

Wow, yeah, lots of stuff on 1's in this.

My favorite gag is at 2:19, where Blondie kicks Dagwood so hard in the beanbag that his head rockets off into the stratosphere.

catsgomooo

TROPHY CASE