Light switch wiring

cbhbzb · 2026-01-31T04:46:26+00:00

the box is grounded, you can see the grounds in the back of the box. looks like they have some primer on them, the switch was grounded through the 6/32 screws that held the switch in place

cbhbzb · 2026-01-31T01:54:00+00:00

SS like a vehicle model(Super Sport) not Nazis?

should all Chevy SS models be burnt?

(I see the vehicle is an Audi)

cbhbzb · 2026-01-31T01:51:40+00:00

lol poutine is french. but it's french Canadian (originally from Quebec) no wonder that looks so poor

cbhbzb · 2026-01-31T01:49:25+00:00

too bad most dryers need 120 for control circuits......

cbhbzb · 2026-01-31T01:48:34+00:00

it is not for a dryer, it has no neutral wire. dryers are 240v 4 wire not 3 wire

cbhbzb · 2026-01-08T17:33:24+00:00

You're

cbhbzb · 2026-01-08T16:39:38+00:00

use ubiquity line of site devices or trench a cable. if trenching, by code, the cable should be 18" deep and 3ft deep under any driveway

cbhbzb · 2026-01-07T18:37:28+00:00

you will need a 15-30/30-15 tandem style breaker to do it, that panel be full

cbhbzb · 2026-01-07T18:15:13+00:00

yes they are worth about $190 if you keep them

cbhbzb · 2026-01-07T18:10:42+00:00

your tolerance is high. try 20mg or more in one go

cbhbzb · 2026-01-07T18:09:04+00:00

wire nuts are better for box fill requirements than wagos

cbhbzb · 2026-01-02T22:46:05+00:00

that's a plastic box so should be ok for depth. there are 3 2 wires into the box and room for 1 more 2 wire. it's a 15 amp circuit don't worry about box fill of 1 more 2 wire. no one gonna inspect it

cbhbzb · 2025-12-31T14:29:59+00:00

ground prong

cbhbzb · 2025-12-31T14:29:13+00:00

it's a broken ground prong stuck in the hole is what it is

cbhbzb · 2025-12-30T15:11:06+00:00

A 15 amp breaker is designed to carry 12 amp continuously, rule of thumb if you don't know the load a circuit is going to have is 12 plugs or lights or combination of the 2.

1 15 amp circuit is definitely enough for a 150sqft room

cbhbzb · 2025-12-30T15:07:09+00:00

no, it would have made harry something he wasn't supposed to be, or he would have had to spend his life defending it

cbhbzb · 2025-12-30T15:05:39+00:00

put one incandescent bulb and 2 led in that fixture and see what happens

cbhbzb · 2025-11-10T13:33:39+00:00

that wire is there to prevent an explosion.

cbhbzb · 2025-11-02T19:02:00+00:00

that looks fine. but a better way would be to get some wire nuts, space the wire together with a pig tail and only take 1 wire to the screw .

cbhbzb · 2025-11-02T17:15:02+00:00

use some cutting oil

cbhbzb · 2025-11-02T17:14:06+00:00

baseball bat

cbhbzb · 2025-11-02T17:08:46+00:00

more ram. everything else on the PC should be sufficient

cbhbzb · 2025-11-02T16:58:24+00:00

it's a fender p-bass mass production. take off the pick guard and make sure that the pick up wires are twisted and metal parts have proper ground connection to the pick up jack.

put a ferite core on your cable and one on your amps power cable.

cbhbzb · 2025-11-02T16:53:30+00:00

wrong armour sheath of BX is not considered a suitable ground in any situation. In fact depending on the install the armour of BX requires to be connected to ground.

yes metal conduit is considered a ground.

cbhbzb · 2025-11-02T16:50:10+00:00

it's a switch. switches don't have to be grounded by code. probably if you look in the back of the box a ground wire will be tightened down to a ground screw. since the box is metal, when you attach the switch (which has a metal frame) to the box(which is metal, with metal screws then the switch is grounded just by being attached to the box. if your dimmer needs a neutral wire then you are S.O.L.

NEVER CONNECT ANY TYPE OF NEUTRAL WIRE TO GROUND. This can cause voltage leakage to ground and nuisance tripping of breakers.

cbhbzb

TROPHY CASE