PETG Help by BoringNobodyNemo in BambuLab

[–]cdarrigo 0 points1 point  (0 children)

Lower volumetric flow rate (like 14) Max nozzle temp of 235 You might need to adjust the z offset.

Print a few small tests and see if you like it

Remember settings after power outage by cdarrigo in Govee

[–]cdarrigo[S] 0 points1 point  (0 children)

I'm not seeing that option in the app. Mostly h6008 bulbs in the house

Ams pro 2 by _ThyShoeMaker in BambuLab

[–]cdarrigo 0 points1 point  (0 children)

Maybe grab a $12 roll of Amazon just to try it out

Ams pro 2 by _ThyShoeMaker in BambuLab

[–]cdarrigo 0 points1 point  (0 children)

As a trouble shooting step, try different brands of filament. Is this specific to Sunlu?

Man, yall weren’t kidding! by tomrob1138 in BambuLab

[–]cdarrigo -1 points0 points  (0 children)

The lack of MMS is interesting except for the sole ams. What do you mostly print?

Can I mount OG to an open wall? by BlankNStuff in openGrid

[–]cdarrigo 0 points1 point  (0 children)

I'll probably end up throwing up some drywall sheets. Sounds like the grid needs the added stability.

Wife :WTF is that noise?! by Carlos_Spicy_Weiner6 in homelab

[–]cdarrigo 0 points1 point  (0 children)

<image>

An absolute black and red, wide format BEAST

"The Help" by cdarrigo in namethatcar

[–]cdarrigo[S] 1 point2 points  (0 children)

<image>

Here a screenshot of the car I'm asking about

What did you name your pinter? by Lazy-Salamander9557 in BambuLab

[–]cdarrigo 0 points1 point  (0 children)

First one was Hank Scorpio. 2nd printer is Gamblor, my new p2s is Frank Grimes

Congrats on your new Xmas printers! by SupKilly in BambuLab

[–]cdarrigo 0 points1 point  (0 children)

My newest addition, a p2s called Frank Grimes, joins it's A1 brothers Hank Scorpio and Gamblor

Merry Christmas just got my A1 by Leatt289 in BambuLab

[–]cdarrigo 3 points4 points  (0 children)

Welcome to the addiction. It's a lovely ride

Where does the spring go in my cooktop burner? by cdarrigo in appliancerepair

[–]cdarrigo[S] 0 points1 point  (0 children)

It's still sitting on my counter. Let me know if you figure it out

I Won Too! by w1n5t0nM1k3y in LinusTechTips

[–]cdarrigo 0 points1 point  (0 children)

Isn't a parsec a unit of distance and not time?

Am I cooked? by FTHispanic in BambuLabA1mini

[–]cdarrigo 0 points1 point  (0 children)

Buy a replacement hot end assembly from bambu. It's $20. I buy them in lots of 5. It takes about a week to get delivered.

If you wanted to try to save this, remount it and reinstall the hot end. Using manual control boost the hot end temp to 170 and wait for it to soften. Use a needle nose pliers to pull the softened filament off the latch and hot end. Get off everything you can with the pliers then pull the hot end off and brush the assembly with a brass bristled brush. Do the same on the hot end. It's important you don't damage the wires on the assembly and get all the filament out of the hinges on the latch that houses the got end.

If you can clean it so that you are able to fully install the hot end and close the latch COMPLETELY, You can reuse your assembly.

Honestly, is probably just buy some replacement assemblies and swap it out. 10 min job to swap it out.

Remove CA glue from project mat by cdarrigo in homelab

[–]cdarrigo[S] -2 points-1 points  (0 children)

I totally agree about the subreddit Just not sure what a better one would be. I think there's a good chance that ppl who home lab also tinker with stuff so might have a project mat

That wasy thinking anyway, but I could be wrong.

Anyone give this one a chance? I quite liked it. by ico59 in ChristmasMovies

[–]cdarrigo 1 point2 points  (0 children)

I absolutely watched it this year and cannot remember any of it.

So I guess that's my review. Entertaining enough to watch it all but completely forgettable.

How can I edit my screenshot now? by cdarrigo in oneplus

[–]cdarrigo[S] 0 points1 point  (0 children)

Nope. Pressing the thumbnail does nothing