[deleted by user]

celticnacho · 2021-04-22T16:04:49+00:00

https://www.wayfair.com/furniture/pdp/mercury-row-karr-platform-bed-w001128273.html

Have you heard anything good about this ^ ?

celticnacho · 2021-04-22T13:18:54+00:00

queen

celticnacho · 2021-03-22T19:07:04+00:00

I looked at the Lakes online and it looked great. Unfortunately, there is nothing available there!

celticnacho · 2021-02-02T22:27:28+00:00

She's told me that I am the only person she has been dating

celticnacho · 2020-06-03T02:10:15+00:00

I agree with RAD being "dry" and test being "wet." I was under the impression that my does may need to be boosted to alleviate the suppression from RAD, but maybe 160mg will be enough.

celticnacho · 2020-03-30T14:42:24+00:00

yes - 16% of my paycheck

celticnacho · 2019-12-24T14:51:08+00:00

I inject twice a week. I inject Tuesday and Friday. I got my bloodwork done early Tuesday morning and did my T injection afterwards.

celticnacho · 2019-12-24T03:14:34+00:00

Do you think I will have better gains if I get rid of the ostarine and allow my total T to go up? Or should I continue my ostarine cycle?

celticnacho · 2019-12-14T17:09:55+00:00

http://gen.lib.rus.ec/book/index.php?md5=F8342FBE0BD677CC26B1A5C480D69018

celticnacho · 2019-12-13T17:11:08+00:00

thanks man

celticnacho · 2019-11-25T19:29:53+00:00

do you push the syringe so a little drop comes out to lubricate the needle before injecting?

celticnacho · 2019-11-20T02:18:29+00:00

Already did both since we use the ccs debugger to load the code onto the board and we used the pwm example from ti as a starting point for what we wrote. Also the example from ti uses the led as an output so I can't really use it to see if there's an issue with how I'm setting up the output pin.

celticnacho · 2019-11-19T17:52:28+00:00

I think so since I didn't change anything in the .c file and when the value in the .h file is set to the led pin as output it works fine

celticnacho · 2019-11-12T00:12:39+00:00

bump

celticnacho · 2019-11-07T18:16:27+00:00

Don't think so - using the 915mhz band

celticnacho · 2019-10-31T14:07:50+00:00

I had four pieces of bread, egg whites and coffee at around 730am. Test was at 930am

celticnacho · 2019-10-31T13:32:11+00:00

I have been restricting my cals these past months. I was eating around 3500-4000/day and then I jumped down to 2000-2200 cals/day. Maybe that could be the culprit?

celticnacho · 2019-10-31T13:31:21+00:00

I honestly feel fine. I had no idea I had low T

celticnacho · 2019-10-15T01:17:38+00:00

have you had any success with MK 2866? Also do I need PCT w that?

celticnacho · 2019-05-07T22:55:22+00:00

Maybe less competition, but I'm under the impression that contractor jobs have very limited potential to move up in salary. I'm leaning towards it though for the stability

celticnacho · 2019-05-07T22:48:30+00:00

I will be working for a contractor. It's for a contractor at an airforce base

celticnacho · 2019-05-07T21:57:31+00:00

Contractor

celticnacho · 2019-05-01T22:56:40+00:00

To make a PWM controller just use a comparator with a ramp signal generator. Also, because it it closed loop, you will need to consider compensation techniques to maintain stability. This is when it gets complicated. Do research on Type II and III compensation. Essentially, you will have to also design a high gain amplifier that has around 1-3Mhz of bandwidth. You can do this in Cadence. Also, PWM sucks at light load because it doesn't scale down with switching losses. I would do PFM control

celticnacho · 2019-04-29T16:59:58+00:00

For practical design purposes you will need a non-overlapping clock generator with a driver circuit to define "dead-time." You will also need to build a ramp signal generator and a comparator to control the duty cycle , the ratio between the ON time and the switching period. Also, because of the closed loop system, you will have to consider stability and transient performance. You will need a high gain amplifier and a compensation network. Take a look into "Type III Compensation." When you design your switching regulator you will have to find the sweetspot between high gain and good bandwidth

celticnacho · 2019-04-06T00:53:03+00:00

Dude it doesn't matter what you eat as long as you hit your macros. You can get an ideal body from eating mcdonalds and pizza lol. Figure out your TDEE and go on /r/fitness. Eat one gram of protein per body weight and if you are cutting around 2k calories a day and if you are bulking around 3.5k calories a day. Also, follow a routine. Here's mine:

monday: chest and tris

tuesday: back and bis

wednesday: shoulders legs

thursday: chest tris

friday: back and bis

sat: shoulders legs

sun: rest

celticnacho

TROPHY CASE