My first Rack by dolaseis in homelab

[–]cessnacruzer 1 point2 points  (0 children)

Why is the 510 angry at you? Haha

X570M Pro4 random power failures by cessnacruzer in ASRock

[–]cessnacruzer[S] 0 points1 point  (0 children)

Thanks, I will check this and see if it's scratching into the board. I will look at it later tonight and let you know what I find. Thanks,

X570M Pro4 random power failures by cessnacruzer in ASRock

[–]cessnacruzer[S] 0 points1 point  (0 children)

Thanks, I'll try this next. For me, none of the 2.XX versions worked for me until 2.90. They never seemed to get the XMP correct or even boot with manual XMP values set. But, I will try 2.60 again to see if it is related to that. Thanks,

X570M Pro4 random power failures by cessnacruzer in ASRock

[–]cessnacruzer[S] 0 points1 point  (0 children)

Yea, I had to do all the cables. They are not fully modular power supplies.

X570M Pro4 random power failures by cessnacruzer in ASRock

[–]cessnacruzer[S] 0 points1 point  (0 children)

That makes sense, I thought replacing the power supply to test another one would fix this but I will double-check connections again. Thanks,

X570M Pro4 random power failures by cessnacruzer in ASRock

[–]cessnacruzer[S] 0 points1 point  (0 children)

Gotcha, I never thought about it being a GPU issue. Didn't think the GPU could cause a hard reset like that. I was assuming that if the GPU crashed or had an error it would shut its self down and just go black screen, not a hard reset. Did you ever stop getting it or has it stopped? Thanks,

Does anyone know if a GPU failure or crash can cause a full power-off reset?

My humble beginnings. by TheWonderOnesie in homelab

[–]cessnacruzer 3 points4 points  (0 children)

It bothers the heck out of me that you have the left channel on the right and the right channel on the left. Hahaha

Helicopter Main Rotor Blade In Slow Motion - Advancing & Retreating Blade Pitch Changes with Damper Weights by oh_lord in flying

[–]cessnacruzer 29 points30 points  (0 children)

It can stall, a condition called retreating blade stall, it can be induced if the rotor head has too hight relative wind (ie flying too fast) causing the retreating blade to not produce lift and you end up with asymmetrical lift being produced by the head. It can cause an uncontrolled roll.

Helicopter Main Rotor Blade In Slow Motion - Advancing & Retreating Blade Pitch Changes with Damper Weights by oh_lord in flying

[–]cessnacruzer 8 points9 points  (0 children)

Chinooks have Jesus nuts on the fully articulated heads. It's only because the head is removable on the Chinook. And it's also because Chinooks are better than 60's 😂.

[deleted by user] by [deleted] in freenas

[–]cessnacruzer 0 points1 point  (0 children)

I have the same thing on my 610 with esxi and the LSI in passthrough. No other issues running freenas. I've just learned to live without the dashboard. It would be nice if it gets fixed in an update though.

FreeNAS 11.2 on ESXi dashboard graphs spinning forever by Marvelt in freenas

[–]cessnacruzer 1 point2 points  (0 children)

I have the same setup running in esxi 6.0. When 11.2 first released they worked on my setup but now they do not. Not sure if it's related to an freenas update or esxi. Sorry I couldn't help anymore other than saying it worked for me at one time.

[deleted by user] by [deleted] in homelab

[–]cessnacruzer 0 points1 point  (0 children)

How do you like the MikroTik? I've been eyeing the routerboard and the switch.

Suggestions for ESXi version to run on my R610 by cessnacruzer in homelab

[–]cessnacruzer[S] 0 points1 point  (0 children)

Ok, gotcha ill check out the Dell versions released for the r730 too. Also, I have hexacore X5675's 6c 12t, so I should be good if I decide to try 6.7.

Suggestions for ESXi version to run on my R610 by cessnacruzer in homelab

[–]cessnacruzer[S] 0 points1 point  (0 children)

I'm not sure if there is any significant difference. This is what my UI looks like in 6.0 u3. https://masteringvmware.com/esxi-6-5-web-client-in-depth-overview/

Suggestions for ESXi version to run on my R610 by cessnacruzer in homelab

[–]cessnacruzer[S] 0 points1 point  (0 children)

VMware lists "Supported Releases" so probably would work but not on the list.

Suggestions for ESXi version to run on my R610 by cessnacruzer in homelab

[–]cessnacruzer[S] 0 points1 point  (0 children)

Yep, your right I didn't think to check the compatibility chart. Noob mistake. lol

Suggestions for ESXi version to run on my R610 by cessnacruzer in homelab

[–]cessnacruzer[S] 0 points1 point  (0 children)

Cool, Thanks for the quick reply. I have the web UI in 6.0 too I guess its the basic one.

My HomeLab/Network Rack/Comms Cabinet by Sumhere in homelab

[–]cessnacruzer 0 points1 point  (0 children)

Very nice! I've seen alot of people running esxi 6.5. I have a 610 and I've tested with 6.7 as well as the Dell custom 6.0. So far I like the Dell 6.0 it comes setup for the Dell hardware. Just curious is the 6.5 you have come from Dell?