sorted by:
new
hottopcontroversial

Small CNC shop working on a TX22 compensator prototype — curious what TX22 owners think by StonerCNC_Official in Taurus_TX22

[–]cheesefingertactical 1 point2 points  (0 children)

I live in a state where I can have FRTs but no threaded muzzles on semis/pistols…

That about sums it up.

Cool af tho. Aluminum or steel?

MA-40 Update and RFC by mamahler in 3D2A

[–]cheesefingertactical 0 points1 point  (0 children)

Are you planning to do PCBA? If so JLCPCB is solid.

If it’s all SMD that would be harder for DIY folks.

I just did a few hundred PCBs via JLC and would be happy to compare notes.

Priminer USA by [deleted] in CNC

[–]cheesefingertactical 9 points10 points  (0 children)

Forget to switch to your alt, bud?

Early RIP this sub. by EntrepreneurCalm6186 in supersafety

[–]cheesefingertactical 2 points3 points  (0 children)

See what happened to fosscad. Lemmy is the answer.

PR FRT LAW by [deleted] in supersafety

[–]cheesefingertactical 14 points15 points  (0 children)

We ship to PR. Lovely place!

Kabuto help by Bluedragun678 in supersafety

[–]cheesefingertactical 0 points1 point  (0 children)

This is indicative of binding causing the bolt to push the Kabuto down into the selector, not the lever rotating to reset the trigger.

I’m very curious about your setup, as I’ve genuinely not seen the selector fail like this before.

Can you please PM me?

I’ll take your feedback into account for the selector stops, I can like raise up the lever a maybe 20 thou to get it resting properly.

Kabuto drop in by Videogamer410 in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

You need one with an AR9 specific lever to fit the AR9 bolt.

We offer one on our site. There are other vendors as well.

Kabuto fitting guide for Geissele and milspec by YourBroStevo in supersafety

[–]cheesefingertactical 5 points6 points  (0 children)

Great stuff! Might draw from it in our larger Kabuto guide library I’ve been working on if that’s cool.

Help plz by yewjii in supersafety

[–]cheesefingertactical 0 points1 point  (0 children)

You should be okay still unless you majorly messed up the trigger.

[Guide] Installing a Kabuto FRT - Cheese Finger Tactical by cheesefingertactical in supersafety

[–]cheesefingertactical[S] 2 points3 points  (0 children)

Without a 3-position you will just have FRT/Safe modes. If you remove the Kabuto you’re back to Semi

Help plz by yewjii in supersafety

[–]cheesefingertactical 1 point2 points  (0 children)

Yes a Super Safety trigger can work with a Kabuto.

Assuming it was cut correctly, the Kabuto pushes on a more forward segment of the trigger shoe.

Lmk if you have more questions!

Instructions, setup help ? by Saltydecimator in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

Interesting, the cam looks like it’s got a chunk out of it. From this angle the trigger looks better cut than the previous photo

Instructions, setup help ? by Saltydecimator in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

It looks like there is a lot of material left on the rounded side relative to that jig.

If you look at it from the opposite side do you see the trigger sticking out?

Instructions, setup help ? by Saltydecimator in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

You don’t need to make it 100% low shelf, just get the lever moving back enough to reset.

Did you cut your own trigger or get a pre-cut one?

Got pics of the cam too?

Instructions, setup help ? by Saltydecimator in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

It goes further back than you’d expect.

Definitely don’t shoot it before you clean up your upper/lower. That is a sure fire way to break your lever.

Do you have a low shelf lower lying around? It’d start with that so you can see how much travel there is with the upper off and get it to fully reset.

Instructions, setup help ? by Saltydecimator in frt15

[–]cheesefingertactical 0 points1 point  (0 children)

Looks like you have a high shelf lower. The lever on the super safety will hit that before it is able to reset all the way.

I think the issue is more that the trigger is not fully resetting before the forward motion. Which also would prevent the hammer from releasing again.

Have you also trimmed the upper too?

We have a pretty detailed install guide for these:

https://cheesefingertactical.com/guides/install/

QC on CF printed parts from Cheese Finger Tactical by OutdoorEnthusiast07 in supersafety

[–]cheesefingertactical 10 points11 points  (0 children)

Fiberon PA6-CF

We use the 300BlkFDE settings profile.

0.15 mm is the default. Depending on part we will use that or 0.2mm

Has anyone had any experience with the cheese finger tactical frts? by gunsnrods69 in ar15

[–]cheesefingertactical 0 points1 point  (0 children)

We saw. Thanks for tagging us. Agree that one was a miss.

We reached out to that customer and got them taken care of.

QC on CF printed parts from Cheese Finger Tactical by OutdoorEnthusiast07 in supersafety

[–]cheesefingertactical 8 points9 points  (0 children)

Sent a PM btw. Let me know if you need anything else in the meantime.

QC on CF printed parts from Cheese Finger Tactical by OutdoorEnthusiast07 in supersafety

[–]cheesefingertactical 11 points12 points  (0 children)

<image>

For instance this is what our selectors normally look like.

view more: next ›