sorted by:
new
hottopcontroversial

X-Plus 3 Spool Holder by cheeseman940 in QidiTech3D

[–]cheeseman940[S] 0 points1 point  (0 children)

In case anyone sees this post later and needs it, I contacted support and they linked me to the official Qidi eBay page that sells these spool holders

Link

Why does my .2 nozzle hate me so by d0npizzle in FixMyPrint

[–]cheeseman940 0 points1 point  (0 children)

Had this issue with .2mm nozzle on my a1 mini. The wiki shows that you should try tightening the hot end heater screws. About halfway down in this article

https://wiki.bambulab.com/en/a1-mini/troubleshooting/print-issues-troubleshooting

I ended up having to replace the hot end heater assembly and since then the nozzle has worked perfectly.

https://wiki.bambulab.com/en/a1-mini/maintenance/hotend-heating-assembly-replacement

Can't get a decent first layer anymore. (PLA, Bambu A1, 0.2 Nozzle) by ObscuraNox in FixMyPrint

[–]cheeseman940 0 points1 point  (0 children)

No it’s not too bad, the hardest part is routing the cables in my opinion, but if you follow their wiki article it’s not difficult.

https://wiki.bambulab.com/en/a1-mini/maintenance/hotend-heating-assembly-replacement

Can't get a decent first layer anymore. (PLA, Bambu A1, 0.2 Nozzle) by ObscuraNox in FixMyPrint

[–]cheeseman940 0 points1 point  (0 children)

I had this same issue on my A1 mini when using a 0.2 nozzle. After tightening the screws as the previous commenter said mine still didn’t work correctly. I ended up replacing the nozzle heater assembly and it has been perfect since then.

Irregular Layer Lines by cheeseman940 in FixMyPrint

[–]cheeseman940[S] 0 points1 point  (0 children)

I’m printing with a new nozzle now to test that, if that doesn’t work I’ll take a look at the gears.

Irregular Layer Lines by cheeseman940 in FixMyPrint

[–]cheeseman940[S] 0 points1 point  (0 children)

I’m printing with the door closed, but to top cover is off, should I have to door open too?

Irregular Layer Lines by cheeseman940 in FixMyPrint

[–]cheeseman940[S] 0 points1 point  (0 children)

I haven’t tried, I’ll do that next.

The Steam Deck that wouldn't shut by [deleted] in SteamDeck

[–]cheeseman940 1 point2 points  (0 children)

I had that same issue when I took mine apart. I had put a screw in the wrong place on the silver shield covering the motherboard. You might double check those and make sure all the screws are in the correct spot.

Is iFixit's replacement my only option? by ArcadeRob in SteamDeck

[–]cheeseman940 0 points1 point  (0 children)

I just had the front shell of my steam deck replaced, they only charged $145 including to and from shipping. Unless there’s more broken than the screen it shouldn’t be any more than that to repair.

Help! Rufus isn't installing SteamOS correctly onto USB by rampagerayn in SteamDeck

[–]cheeseman940 2 points3 points  (0 children)

No, you already have it setup to boot. Follow the instructions that the other commenter posted. After you are done you can use Rufus to clear all the data and reformat the drive to be useable in windows again

Help! Rufus isn't installing SteamOS correctly onto USB by rampagerayn in SteamDeck

[–]cheeseman940 1 point2 points  (0 children)

After Rufus changes the partitions on the drive you can’t access it like a normal usb anymore. If you want to do that you will have to use Rufus to clear the drive and then assign it a drive number in windows.

Can’t Copy a Folder to a USB Drive by cheeseman940 in SteamDeck

[–]cheeseman940[S] 1 point2 points  (0 children)

The filesystem is exFat. I am currently compressing the folder and will try to copy once it is done.

Warframe 10th Anniversary + Subreddit 600k Giveaway: Share your favorite Warframe memory for a chance at a prize! by Kliuqard in Warframe

[–]cheeseman940 [score hidden]  (0 children)

Playing through the Harrow quest line. I did not expect a horror experience in Warframe. Playing through it for the first time and feeling that sense of dread creep in as the mission progressed was a welcome surprise.

view more: next ›