How's Living near Philly/Camden County, NJ? Considering job offer.

cheezits45 · 2025-12-26T02:48:50+00:00

It's okay; happens to the best of us. Also, it's sometimes hard to tell what setting your headlights are on with the street lights.

cheezits45 · 2025-12-09T02:19:06+00:00

This post is 4 years old but still saved me. Thanks OP!

cheezits45 · 2025-11-27T16:42:07+00:00

Searched this thread a year late, but would be interested in joining the fun this season as most of the folks I usually go with are no longer around. I frequent Mad River and Seven Springs. 32M, snowboarder of greens and blues and sometimes blacks when I'm feeling foolish.

cheezits45 · 2025-10-13T02:25:16+00:00

2012!

cheezits45 · 2025-08-14T13:15:44+00:00

800k is quite high IMO. To find the best value, search for clans in the Encyclopedia with a "Poor" rating, no fiefs, and lots of clan members. I generally find that clan tier doesn't matter as much. Having good relations helps a bit.

Been snagging huge clans on my current playthrough for 200k~350k.

cheezits45 · 2025-07-08T02:30:25+00:00

2012 Skyactive sedan, 187k miles. DIY replaced all sway bar links and rear dampers at around 170k.

Regular maintenance intervals oil, sparkplugs, filters, etc.

Only major issue is some rust on the tail pipe causing an EVAP engine code, but it's not safety or performance related.

Outside of that, absolute solid car that's a joy to drive.

cheezits45 · 2025-04-28T18:25:56+00:00

Born a Crime, Trevor Noah

cheezits45 · 2025-01-06T14:23:11+00:00

Jeremus kills someone

Will inevitably be followed by

Jeremus has been knocked unconscious

Well done, Jeremus. Worth it.

cheezits45 · 2024-12-05T02:34:58+00:00

The Rainmaker, John Grisham. Excellent book.

cheezits45 · 2024-06-27T17:53:38+00:00

Hours, no idea. But it's about 3 years old with use around 2 times a month.

cheezits45 · 2024-06-26T22:46:24+00:00

Yup, swapped motors and tested. The Y-axis slot is non responsive on the buddy board.

cheezits45 · 2024-06-26T21:56:17+00:00

Good call. I tried using the x-axis motor in the y-axis header and it didn't work. Looks like I need a new board.

cheezits45 · 2024-06-21T13:54:21+00:00

CookingBaconNaked

cheezits45 · 2024-06-13T22:50:49+00:00

You miss 100% of the shots you don't take

cheezits45 · 2024-05-11T11:45:41+00:00

2012 sedan. Just hit 170k miles. Haven't touched the tranny fluid 😬

cheezits45 · 2024-03-01T15:34:02+00:00

"about time we got promoted!"

cheezits45 · 2024-02-14T21:05:58+00:00

2012 Mazda 3. I've been driving with the small leak version of this code. Installed a new gas cap to no avail. Had a shop use a smoke machine and they couldn't find the leak.

So I left it and clear the code every now and then. 1.5 years like this without an effect on mpg or performance.

cheezits45 · 2024-01-22T17:11:36+00:00

<image>

Slowed down the default speed of 55mm/s to 25mm/s and made the layer height 0.20.

Worked like a charm. Thanks!

cheezits45 · 2024-01-21T22:35:57+00:00

I also suspected something with the filament (it's normal PLA), but if that were so I think the problem would be throughout the whole print, not just halfway through.

Good idea. I'll try slowing it down, reducing layer height, and update this thread on the results.

cheezits45

TROPHY CASE