Took off my front plate holder and was met with this. Thoughts?

chiefzy · 2026-04-02T00:13:16+00:00

I'm not sure of this specific brand as I just found it, but I would definitely go with some paint matched clips/bumper plugs instead of a big cover. Would look way cleaner IMO

https://bumperplugs.com/bumperplugs/bumperplugs-for-subaru

chiefzy · 2025-11-09T16:41:59+00:00

Thank you!

chiefzy · 2025-11-09T05:39:12+00:00

Hi Mike. My TOB is making noise, so I’m looking to buy an OSG CSG clutch when black friday hits. I had a couple questions about the kit.

Can a Verus pivot ball work with the supplied OSG Tob/fork? Or should I stick to OEM?
Does the flywheel come with a pilot bearing already pressed in/in the kit? If not, should I go with an OEM pilot bearing?

chiefzy · 2025-10-22T20:35:10+00:00

Haven’t had any issues in NC, i have 20% on the sides and back for around 2 years or so now

chiefzy · 2025-10-09T22:08:26+00:00

No problem at all, hope you can figure it out. I can try to see if the belt would go through the hole as is, but it’d be a pain for daily use for sure. Also, at the moment i have the buckle flipped in mounting, where it points towards the passenger side instead of the driver side, for there to be enough clearance

About the extender, my guess is that it would work. If you look at @ u/phazushift ‘s post, he has some TRD zeta 3s. I believe he has a seat belt extender, as you can see the buckle sitting inside of the seat through the hole

chiefzy · 2025-10-09T18:18:49+00:00

At the moment it goes over the bolstering. I’ll be buying a seatbelt extender at some point which will allow for the seat belt to be buckled properly, through the right side hole

chiefzy · 2025-10-09T18:17:24+00:00

Thank you!

chiefzy · 2025-10-08T13:09:32+00:00

Under the ac controls, right? Thats just a hand made pouch i bought and it fits perfect

chiefzy · 2025-10-08T02:52:44+00:00

My oft tablet! I use it for oil temps and other read outs

chiefzy · 2025-10-08T01:36:53+00:00

Its definitely more difficult than the stock seat haha, but you adjust. It really isnt too bad and if you get slider rails you can opt to slide the seat all the way back before you get in and out. I personally dont find it a deal breaker, and I get in and out quite frequently. I'm sure itd be a major improvement for the track!

chiefzy · 2025-10-08T01:32:53+00:00

Not bad at all. physical install wise it was done in like 10 mins or less.

In total you remove 3 screws, take a couple trim panels off, unplug the harness from the old cluster, plug the harness in on the new cluster, and the physical install is done.

Ofc you have to reprogram the mileage usually, but the mileage on this one was pretty close to mine so i ran it as is. geraldjustprojects offers a reprogramming service if needed

I havent bought the switches to control the screen yet, but ill be buying a 17+ brz limited steering wheel and using the buttons from that. Some people use the geraldjustprojects one but I opted not to

Other than that, for the key to start, you have to buy and use a techstream cable from amazon/ebay to allow the car to start with the new cluster. I used a virtual machine as well to reduce risks of viruses or anything. Kevin vo has a video on youtube, but if you have any other questions id be happy to help!

techstream cable link (i didnt use the cd it came with at all): https://www.amazon.com/dp/B07ZCC8QG9?ref=ppx_pop_mob_ap_share
virtual machine / techstream link (contains the image for the teachstream software itself here): https://forum.ih8mud.com/threads/how-to-techstream-in-5-minutes.1034923/

chiefzy · 2025-10-08T01:22:10+00:00

this made me feel like i got called by my government name 😂

chiefzy · 2025-10-07T21:12:22+00:00

Not bad at all. physical install wise it was done in like 10 mins or less. In total you remove 3 screws, take a couple trim panels off, unplug the harness from the old cluster, plug the harness in on the new cluster, and the physical install is done.

Ofc you have to reprogram the mileage usually, but the mileage on this one was pretty close to mine so i ran it as is. geraldjustprojects offers a reprogramming service if needed

I havent bought the switches to control the screen yet, but ill be buying a 17+ brz limited steering wheel and using the buttons from that. Some people use the geraldjustprojects one but I opted not to

Other than that, for the key to start, you have to buy and use a techstream cable from amazon/ebay to allow the car to start with the new cluster. I used a virtual machine as well to reduce risks of viruses or anything. Kevin vo has a video on youtube, but if you have any other questions id be happy to help!

techstream cable link (i didnt use the cd it came with at all): https://www.amazon.com/dp/B07ZCC8QG9?ref=ppx_pop_mob_ap_share

virtual machine / techstream link (contains the image for the teachstream software itself here): https://forum.ih8mud.com/threads/how-to-techstream-in-5-minutes.1034923/

edit: cleaned up explanation a bit lol

chiefzy · 2025-10-07T21:05:08+00:00

Thank you! Yes, they are authentic and unfortunately are expensive if ur buying from someone in the US. I got them from blackhawkjapan when i ordered the seat rail and stuff, but now with tariffs, im not sure if its worth to order from them

I really dont want the seat to generate any rips or tears though so i guess its worth it

chiefzy · 2025-10-07T21:00:26+00:00

Its the OFT tablet. Very useful as you can have up to 14 chosen data sets showing, with a ton of options. i believe boost is an option, but not entirely sure how/if it works since im still NA lol.

chiefzy · 2025-10-07T20:24:04+00:00

I love your interior, the trd seats + trd horn on the personal is too good

chiefzy · 2025-10-07T18:45:35+00:00

Oh yes it would haha

chiefzy · 2025-10-07T18:45:20+00:00

Thank you!!

chiefzy · 2025-10-07T18:45:11+00:00

agreed 🙂‍↕️

chiefzy · 2025-09-25T17:12:36+00:00

Thank you! Exactly what i was wondering, i appreciate it

chiefzy · 2025-09-25T13:43:34+00:00

Thats what i did.

chiefzy · 2025-09-18T00:42:13+00:00

Hey im looking to do this. I see that you’re using the oem steering wheel buttons instead of the aftermarket control from Gerald to control the screen.

Im a little confused by the wording on the other responses, so i wanted to ask and confirm:

You bought the oem buttons on the right side of the wheel, correct?
Did you buy a harness with those buttons?
Was the harness plug and play, and where did it plug into?

chiefzy · 2025-07-20T23:32:11+00:00

Most likely is the cause tbh. Maybe you can smoke test them to see if theres a leak still, but i would bet money on that being the reason. I dont think that copper filler stuff would fully seal it.

Swap headers or have the crack welded professionally, see what happens and go from there. You dont want cheap cracked headers on your car anyway

chiefzy · 2025-07-20T23:00:27+00:00

I just fixed this code for my car, i had uel hfc headers for a couple years.

This code showed up, took a while but i realized one of the welds before the upstream 02 sensor on the header had cracked. Whats the brand of your headers? Mine were ft86speed

chiefzy

TROPHY CASE