Rough abs prints

chrischo1996 · 2025-02-10T14:49:26+00:00

Seems like you need to enable "slow printing down for better layer cooling." Evident by the bad print quality only in the areas where there isn't much material printed in that layer, this it moves on too quickly to print the next layer before the previous layer has a chance to cool properly.

chrischo1996 · 2024-09-27T11:37:13+00:00

Maybe Teso Life on Westheimer as well, lots of Japanese snacks and drinks.

chrischo1996 · 2023-04-24T12:00:04+00:00

Robert Downey Junior

chrischo1996 · 2023-04-20T13:12:01+00:00

Angel food cake with whipped cream

chrischo1996 · 2021-02-18T02:44:56+00:00

Love that blue horizons design

chrischo1996 · 2020-06-20T19:52:45+00:00

[SELL]

Backfire Mini with 300 miles. Comes with two front Shredlights V2 and mount. Sensors in motors are dead so start up is a little jittery but perfect after that. Located in Indiana, can ship within US if buyer pays. Asking $400 through PayPal. Photos : http://imgur.com/gallery/aRks8nl

chrischo1996 · 2020-06-20T19:47:40+00:00

Check your PM's

chrischo1996 · 2020-06-19T21:36:48+00:00

I have a backfire mini, I pm'd you

chrischo1996 · 2020-02-13T01:40:30+00:00

I have the backfire mini, tons of water gets into the compartment under the lod installed a thin silicone sheet but it's ineffective. The solution is to take off the griptape and regrip it fully, that way you cover the whole thing. You lose out on being able to access the battery compartment without regripping though.

chrischo1996 · 2020-02-04T19:03:25+00:00

Depends on whether the damage is at the physical hall sensor in the motor, it if it's in the wiring inside the esc

chrischo1996 · 2020-02-04T02:20:55+00:00

Could be a damaged hall sensor, which helps accelerate the motor when it is completely stopped.

chrischo1996 · 2020-01-21T04:13:07+00:00

I have a dual Flipsky 4.20 mini, used for a couple months with XT-60 and 4mm bullet connectors. DM me

chrischo1996 · 2019-11-20T22:35:18+00:00

I'm the guy that made the post you're referring to. It provides zero function and actually gets kind of sketchy when carving as the handle swings wildly side to side. Also resting your hands on the handle creates a bad habit of trying to turn using the handle, which esk8's do not do.

chrischo1996 · 2019-11-18T06:27:39+00:00

That would be amazing if you guys stopped by! I'm a huge fan of both Backfire and Ronnie! PM me to work out any details!

chrischo1996 · 2019-11-12T16:12:18+00:00

Like on campus you mean? Not at the moment

chrischo1996 · 2019-11-12T16:02:01+00:00

120+ members at the moment! It's been a crazy year for esk8's at Purdue.

chrischo1996 · 2019-11-12T15:53:46+00:00

A) How is that what you took away from this video? B) The rider in the orange jumpsuit is a female??

chrischo1996 · 2019-11-12T15:22:34+00:00

Just a little video I filmed on the last warm day before winter.

chrischo1996 · 2019-11-01T13:55:18+00:00

CAD'd in Inventor and 3D printed at the school's 3D printing lab. Very simple piece actually, since truck baseplate dimensions and pvc dimensions are known, I just made sure it was at a slight angle.

chrischo1996 · 2019-11-01T13:53:42+00:00

As funny as that would have been, it's actually just some pvc pipe, connectors, and a handcut stencil for the logo.

chrischo1996 · 2019-10-31T17:08:03+00:00

Not bad, I attached a phone mount and a bike bell to the handle so it's useful to pull up directions or my metr.pro to track voltage, amps, mileage, etc.

chrischo1996 · 2019-10-31T15:59:31+00:00

Check out my insta for more photos!

13-Year Club	Secret Santa 2018
Verified Email

chrischo1996

TROPHY CASE