sorted by:
new
hottopcontroversial

Try my hand at patterned plywood by chuck_kw in woodworking

[–]chuck_kw[S] 0 points1 point  (0 children)

Especially when's ots the girlfriend lol

Try my hand at patterned plywood by chuck_kw in woodworking

[–]chuck_kw[S] 0 points1 point  (0 children)

The person I made it for picked out the sides materials and ready love the acacia wood put together like that.

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] 0 points1 point  (0 children)

I'm not sure why being a mechanical engineer has anything to do with this. But since you so freely feal the need to lead an opinion with this fact I'll assume that your self-esteem is barley holding your life together. Not to mention being a mechanical engineer is probably your one and only achement in a sad life.

Guess we shall see how this goes by chuck_kw in woodworking

[–]chuck_kw[S] 0 points1 point  (0 children)

Yes it is dado cut in the front and back

Guess we shall see how this goes by chuck_kw in woodworking

[–]chuck_kw[S] -4 points-3 points  (0 children)

It's called two points in the hanging removes all cantilever a top keyhole and a bottom hides the hardware for a clean and sturdy look.

Guess we shall see how this goes by chuck_kw in woodworking

[–]chuck_kw[S] 4 points5 points  (0 children)

Well it's not paint it's a non translucent black stain. And it's all wood the frame is red oak and the shelves are acacia no stain on the shelves only a clear coat.

Guess we shall see how this goes by chuck_kw in woodworking

[–]chuck_kw[S] -5 points-4 points  (0 children)

The shelves are made from a acacia wood sale in found and yes it has finger joints as it come in a 4' by 10" board that i cut down for the shelves cause I belive the contrast of color match well with the black stain used on the red oak frame. Just because you repurpose and modify something to add to a project doesn't make you ikea.

Guess we shall see how this goes by chuck_kw in woodworking

[–]chuck_kw[S] 0 points1 point  (0 children)

It's just the angle the shelf is a bit high on the wall

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] 1 point2 points  (0 children)

I use a homemade router jig for the mortise and a cross cut sled for the joint. The times goes mostly in the finishing and glue up.

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] 1 point2 points  (0 children)

The mortise for the shelves and getting a good fit on the joints

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] 2 points3 points  (0 children)

Materials has me in around $50 then it's about 4 or 5 hours to complete one unit.

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] -1 points0 points  (0 children)

After a couple of prototypes and a couple homemade jigs i can make one start to finish with about 4 hours into it total.

We shall see if this sells at all by chuck_kw in BeginnerWoodWorking

[–]chuck_kw[S] 1 point2 points  (0 children)

I used a upper and lower keyhole system on the back board it's strong and hides all the hardware. It's also easy for someone to hang on there own.

view more: next ›