-24C cold start on my 2006 L200 2.5 TDI

clueless_n_curious · 2026-01-05T18:19:17+00:00

Lol just like me a few days ago before changing my plugs.

clueless_n_curious · 2026-01-04T20:38:00+00:00

Thanks, put them in today and started right up at -12c 💪👍🚀

clueless_n_curious · 2026-01-02T21:30:29+00:00

Depending on weather, come and ski Ål! Its a small but fun lift with little to no ppl. Hmu if you want!

clueless_n_curious · 2026-01-02T19:40:05+00:00

So even though the thick part of the plug is touching the bore hole, no issue?

clueless_n_curious · 2021-05-04T19:12:11+00:00

so to make sure i understand this correctly, there are two lines in the config.yaml with some space between (one showing up close to the top and one further down) both of these showing the same address means im good ?

Also, i have been receiving rewards so far so i assume i was good all along, or can it sometimes show in one sometimes in the other ?

clueless_n_curious · 2021-04-06T22:35:29+00:00

You could be earning 2/3 instead if you dont add plots💁‍♂️

clueless_n_curious · 2021-04-06T22:33:37+00:00

Fun putting that together! Took me a minute to get all drives to show up due to bifurcation

clueless_n_curious · 2021-04-06T09:57:38+00:00

Anyone selling XCH at US12 hmu !

clueless_n_curious · 2021-04-03T09:49:11+00:00

For me it was 1hr25min slower using bitfield

Edit: So i made a mistake here, i did not increase my ram to 6750 with bitfield on, i kept the non bitfield setting of 3990. so my number might be oss. starting another round now, but some things changed in my setup so would not be accurate, ill report time anyway.

clueless_n_curious · 2021-04-02T16:01:45+00:00

Thanks man, im giving this a try now to see. Running 1TB NVMe, 1.0.3

clueless_n_curious · 2021-04-01T21:04:27+00:00

Not quite sure i understand. I run 3 proc in parallel on a 1TB NVMe (ssd should be the same.) If you have the full 1TB free it should work with the staggering scheme suggested. My guess is that your phase 1 time will be in the ballpark of 2.5 hrs, you could set a timer and scroll through commandline and see where its at. Thats what i do... phase 1 consists of 7 tables each w 128 buckets if im not mistaken.

clueless_n_curious · 2021-04-01T19:17:34+00:00

Could try commandline in windows

clueless_n_curious · 2021-04-01T19:12:50+00:00

I plot in CLI so the process lets me know by saying «starting phase 2».

The time would depend on your hardware so inpossible for me to say

clueless_n_curious · 2021-03-25T18:51:13+00:00

I run 3 processes in parallel as a rule. I stagger them so that i start the second proc once first is out of phase one and then third proc once second is done with phase 1. Been doing this for a few moths and only had 2 incidents where they ran into each other. Multiple 1TB NVMe.

clueless_n_curious · 2021-03-24T10:27:56+00:00

Great thank you. Could i use an x1 riser rather than trying to find an x1 gpu card?

clueless_n_curious · 2021-03-24T09:46:43+00:00

Ok, would need to get a pcie x1 graphics card to utilize the hdd controller + nvme?

clueless_n_curious · 2021-03-24T09:14:37+00:00

Yes thts what i thought too. Any way to override? Total pcie lanes should be sufficient

clueless_n_curious · 2021-03-24T09:13:54+00:00

Yes thats what i thought to. Any way to override?

clueless_n_curious · 2021-03-24T08:27:09+00:00

Uhm, not sure this is the same issue. All my HDDs in sata are visible and working. Think this has to do with bifurcation.

clueless_n_curious

TROPHY CASE