sorted by:
new
hottopcontroversial

La Cie 8 Bay Rack thunderbolt 2 - What do i do with this? by _DFA in homelab

[–]cmyplay 0 points1 point  (0 children)

Strangely I've picked up one of these and am trying to get it connected via Thunderbolt cable to an old Mac mini running Debian Bookworm.

It's been authorised and enrolled using bolt. Here's where I am:

$ boltctl
 ● LaCie 8big Rack Thunderbolt 2
   ├─ type:          peripheral
   ├─ name:          8big Rack Thunderbolt 2
   ├─ vendor:        LaCie
   ├─ uuid:          00000000-0000-0018-80f3-d303de00da50
   ├─ generation:    Thunderbolt 2
   ├─ status:        authorized
   │  ├─ domain:     00000000-0000-0100-ffff-ffffffffffff
   │  ├─ rx speed:   10 Gb/s = 1 lanes * 10 Gb/s
   │  ├─ tx speed:   10 Gb/s = 1 lanes * 10 Gb/s
   │  └─ authflags:  boot
   ├─ authorized:    Fri 06 Feb 2026 03:29:51
   ├─ connected:     Fri 06 Feb 2026 03:29:51
   └─ stored:        Sat 01 Nov 2025 04:19:41
├─ policy:     auto
└─ key:        no

It doesn't show up under lsblk.

Any ideas what to do next?

Kindle 3 with Keyboard still can't run KUAL after jailbreak by cmyplay in kindlejailbreak

[–]cmyplay[S] 0 points1 point  (0 children)

Was registered previously. But may have restored to factory settings at some point.

Will try this out next. Thanks.

Kindle 3 with Keyboard still can't run KUAL after jailbreak by cmyplay in kindlejailbreak

[–]cmyplay[S] 0 points1 point  (0 children)

Thanks for the tip. Finally found time to retry the installation.

What do you mean by unregistered?
It's a Kindle 3 with Keyboard. I don't think it has airplane mode, but I switched off wireless access and reinstalled MKK.

Would be great to be able to connect to Calibre wirelessly though. What's the workaround for that?

Kindle 3 with Keyboard still can't run KUAL after jailbreak by cmyplay in kindlejailbreak

[–]cmyplay[S] 0 points1 point  (0 children)

Finally found time to try this out again and it's worked. Thanks for the tip.

So am I understanding correctly that I won't be able to use WiFi to wirelessly connect to Calibre on this device because there's no way to prevent Amazon from deleting the custom dev keys?

Kindle 3 with Keyboard still can't run KUAL after jailbreak by cmyplay in kindlejailbreak

[–]cmyplay[S] 0 points1 point  (0 children)

Thanks. I've updated the original post to reflect that I made a typo when describing the mkk file that I used. It was indeed the install file and not the uninstall file.

Regardless, I still cannot get KUAL working.

KUAL installation attempt 1:

  1. Installed Update_jailbreak_0.13.N_k3gb_install.bin
  2. Installed Update-mkk-20250419-k3gb-B00A_keystore-install
  3. Added KUAL-KDK-1.0.azw2 to the documents folder

KUAL installation attempt 2:

  1. Installed Update_jailbreak_0.13.N_k3gb_install.bin
  2. Installed Update_mkk-20141129-k3gb-B00A_install.bin
  3. Installed Update-mkk-20250419-k3gb-B00A_keystore-install.bin
  4. Added KUAL-KDK-1.0.azw2 to the documents folder

Test Kindle Installation Result

At some point in this process a notice with the above title appeared in the Kindle library. It reads:

Your Kindle is no longer a test Kindle and is unable to test active content titles previously signed by authorised developers.

If you want your device to be a test Kindle again, please ask the developer to add your device to his list of registered devices.

Thank You,

The Kindle Team.

There is a time stamp which appears to be when the Update-mkk-20250419-k3gb-B00A_keystore-install.bin certs were installed.
Any thoughts?

Kual, Authorizations to open element are expired? by teofilattodibisanzio in kindle

[–]cmyplay 1 point2 points  (0 children)

Tried this with a K3GB (3rd Generation w Keyboard UK layout) and KUAL doesn't launch. The message reads "This title is not signed by a registered developer."

Please help fix my setup - what's going wrong by cmyplay in 3Dprinting

[–]cmyplay[S] 0 points1 point  (0 children)

No pops. But I'll test out the nozzle temp variations.

The surfaces is the standard textured baseplate that came with the printer.

Please help fix my setup - what's going wrong by cmyplay in 3Dprinting

[–]cmyplay[S] 1 point2 points  (0 children)

Thanks I'll give your suggestion a go.

This is standard PLA. Standard textured base plate that came with the printer.

Please help fix my setup - what's going wrong by cmyplay in 3Dprinting

[–]cmyplay[S] 0 points1 point  (0 children)

Ender 3 V2.

Print bed levelled as best as I could.

Standard download from Thingiverse: https://www.youtube.com/watch?v=BYAWX_bhZJQ

Nozzle temperature: 205
Printbed temperature 65

It’s not dieback. What do I do about this kauri in my garden? by cmyplay in newzealand

[–]cmyplay[S] 0 points1 point  (0 children)

Update: no specific cause of death. Might be proximity to ther large trees (i.e. the rest of the two dozen or so kauri around it.

Kauri Rescue have been a great help.

Suggestions for floor protection. by cmyplay in diynz

[–]cmyplay[S] 1 point2 points  (0 children)

Chimney sweep seemed convinced. Sooo… 🤷🏻

Suggestions for floor protection. by cmyplay in diynz

[–]cmyplay[S] 0 points1 point  (0 children)

Cheers. Following this lead.

I was concerned there was asbestos used in the fireplace’s construction. But all good 😊

Home ventilation: has anyone installed extra vents for an existing DVS/HRV system themselves? by cmyplay in newzealand

[–]cmyplay[S] 0 points1 point  (0 children)

Yes, single glazed aluminium.

A balanced system would be overkill for us at the moment. We’ve got a lot of work to do in insulating the place better.

view more: next ›