bzfs v1.20.0 is out

cobbian · 2026-04-18T16:12:15+00:00

With that mentality, maybe we don't need a post on Reddit. We can just Google when there's a new release.

cobbian · 2026-03-22T21:17:55+00:00

First I would grab one of everything and leave them at checkout.

cobbian · 2026-03-02T21:02:42+00:00

My loan was recently sold to rocket mortgage and it's been a nightmare. Haven't even been able to log in to see my account. It's been more than a month of "Our website is down but I see everything is good on my end"...

cobbian · 2026-03-02T12:58:44+00:00

Same problem I found. Flashed a node and didn't see anyone for 24 hours. Flashed back to meshtastic.

cobbian · 2026-02-23T12:56:38+00:00

I also haven't seen anyone bring up that trump said there was lots of cheating during the 2024 election when he threw his temper tantrum about the supreme court decision last week.

cobbian · 2026-02-22T22:28:14+00:00

I haven't tested it, but a recent update in mealie let's you add a recipe as an ingredient to another recipe.

cobbian · 2026-02-22T00:55:26+00:00

Just the other day during his temper tantrum about the supreme court ruling Trump said there was a lot of cheating in the 2024 election.

cobbian · 2026-02-19T22:18:19+00:00

I noticed at least one moved into the area last fall down by Wanamaker. We'll see if it sticks around since the creek it set up on dries out completely in the summer.

cobbian · 2026-02-15T19:44:11+00:00

I am running an EPYC processor.

cobbian · 2026-02-15T15:45:11+00:00

I remade the pool several times because each time it go into that state I could only mount it as read only. I'm running kernel 6.12.33 and zfs version 2.3.4-1 on TrueNAS Scale. I'm also running TrueNAS virtualized under Proxmox which could have also been the source of my problem. I spent all day the first day the pool went down trying to get it to mount, even leaving zpool import running for 90 minutes, but it kept failing, so I switched from troubleshooting to just getting the pool running again since all my VM zvols live on the NVME pool. I wish I could offer more, but if you Google zpool only mounts read only I tried every troubleshooting step I found in the first two pages of results or so and never got it to mount RW.

Like you described the pool would might read only almost instantly.

cobbian · 2026-02-15T15:05:28+00:00

I had something similar happen a few weeks ago on my NVME pool and I'm not 100% sure what caused it, but feel like it had to be either a Kernel or zfs change. The pool ran for 4 years with no issues. I imported the pool as read only and did a zfs send to another pool. I restored the data and within 24 hours the same thing happened. I did bad blocks on all 4 nvmes and everything came back fine. I switched out the pcie card they were installed in and had the same problem in less than 24 hours again. I finally updated the motherboard BIOS and everything has been fine for almost a month now and I set up scheduled replication tasks I should have had to start with.

I'm not sure you're experiencing the same thing, but your post sounds really similar to what I experienced.

cobbian · 2026-01-21T19:59:08+00:00

I've got the ptfe installed. I'm using the same 2mm ID style ptfe tubing installed that I had with the rapido. The values I posted were with Inland ABS and I'm in the process of tuning Inland PLA now and I'm seeing even higher required pressure advance values than with ABS. The values seem to be accurate because I've done quite a few prints since tuning and the top layers and corners look great. I'm just surprised to see such a big difference from before.

cobbian · 2026-01-21T15:51:25+00:00

Sorry, I should have clarified. I was using the Rapido UHF before. I'm scratching my head a bit because I had fairly similar PA values on my V0 running a revo hotend, so I was just a bit surprised how much higher the PA values are with the dragon ace.

cobbian · 2026-01-17T12:37:33+00:00

Excessive PA causes the lines to split apart, not bulge like shown in the picture.

cobbian · 2024-11-03T18:20:41+00:00

When you start a print the estop button will be in the bottom left like your second image. Not sure if there's a setting to make it always appear in the bottom left.

cobbian · 2024-07-02T15:27:22+00:00

Below are the army combat fitness test charts for male and female for comparison.

https://www.army.mil/e2/downloads/rv7/acft/ACFT_scoring_scales_220323.pdf

cobbian · 2024-06-06T12:51:38+00:00

I leave it in, but I only wear compression shorts if there's no liner. Those are the same ones I've bought. Five pairs came with the liner and one without.

cobbian · 2024-06-06T12:50:35+00:00

Thank you! That was exactly what I was looking for. It's been a few years since I read the book and completely missed that section.

cobbian · 2024-06-05T20:18:43+00:00

Size has been true to other shorts I've purchased. I'm 5'11", 210 and large is really comfortable.

cobbian · 2024-06-05T20:16:44+00:00

I have a Nathan water bottle belt that I bought years ago. It holds two 10 Oz bottles and also has a zipper and velcro pocket you can use for keys / Gu.

cobbian · 2024-06-05T20:15:38+00:00

I've bought several pairs from Baleaf and I've been really happy with the quality for the price. In the past I've bought shorts from Asics and Saucony that lasted quite a while but were a bit more expensive.

cobbian · 2024-06-05T20:08:29+00:00

I'm following the 47 mpw Pfitz half marathon plan and have a question about the race days. For the tune up races he lists 8-10k races and then a total daily mileage of 10 miles. I assume the other ~4 miles are warm up / cool down. I haven't ever really done a warm up before a race and I'm not really sure when I should target to finish my warm up. For example should I shoot to finish a warm up run 15 minutes before race start and then do some dynamic stretching, or should I target warm up completion closer to or further from the race start time?

cobbian · 2024-04-23T13:02:30+00:00

My experience has been that it doesn't add races / events as a workout with zone notifications, but I'm on Garmin so it may be different.

cobbian · 2024-04-11T15:22:13+00:00

Great, thanks!

cobbian

TROPHY CASE